Manuals / Brands / Marine Equipment / Fish Finder / Humminbird / Marine Equipment / Fish Finder

Humminbird 150PT, 160pt, 190C PT, 190CPT Attaching the Mount to the Base, Installing the Handle Onto the Base

1 44

Download 44 pages, 928.8 Kb

3.Using a socket wrench and a Phillips screwdriver, secure the PiranhaMAX™ mount to the base with the four included 3/4” screws, lock washers, and nuts. Hand tightenonly!

Attaching the Mount to the Base

PiranhaMAX™ Mount (tilt OR tilt and swivel)

Base

4.Install the handle onto the base, so that the curved part of the handle faces towards the back of the base, towards the battery well. Use the four included #8-32 x 7/16" screws, two on each side, to attach the handle to the base(see the illustrationsInstallingthe HandleOntothe Base and Sliding in the Handle). Hand tighten only!

Installing the Handle Onto the Base

Sliding in the Handle

NOTE: The handle is keyed so that it only fits onto the base in one direction.

Contents

Page Thank You CAUTION: WARNING WEEE DIRECTIVE: © 2008 Humminbird®,EufaulaAL, USA. All rights reserved Table of Contents PiranhaMAX™ Portable Case Assembly Stowing the Portable Transducer Installing the Portable Case on the Boat Connecting the Transducer and Power Cables The Menu System Light (Setting Not Saved in Memory) Depth Range (Setting Not Saved in Memory) Chart Speed (Setting Saved in Memory) Contrast (Setting Saved in Memory) Page PiranhaMAX™ Portable Case Assembly •Assembling the PiranhaMAX™mount •Assembling the base and handle •Assembling the control head to the base and handle •Routing the cables in the base 1.Assembling the PiranhaMAX™ Mount Tilt and Swivel PiranhaMAX™ Mount 2.Assembling the Base and Handle Punching Holes Attaching the Mount to the Base Installing the Handle Onto the Base Assembling the Control Head to the Base and Handle Rear View 4.Routing the Cables in the Base Attaching the Battery Tie-DownStraps Pulling the Cables Through the Base Installing the Cables Onto the Base Tying Down the Cables 5.Assembling the Portable Case 6.Charging and Installing the Battery Installing the Battery 7.Assembling the Transducer Mounting Bracket Transducer Knuckle Positions Assemblingthe PortableBracket below). Hand tightenonly Assembling the Portable Bracket Ratchets Placed in Position 1.Connecting the Transducer and Power Cables to the Portable Case Plugging in the Transducer Connecting the Spade Clips) 2.Attaching the Portable Case to the Boat PortableCaseAssembly 1.Testing the Transducer Prior to Installation 2.Mounting the Portable Transducer on the Boat Portable Transducer Mount Portable Transducer Mount Transducer Running Angle Transducer Tie-DownStrap) Moving the Portable Fishfinder 2.Remove the case from the surface mount 4.Unplug the power cable when not in use Powering ON and OFF •Use Start-Upfor on the water use - Water Surface Line - Structure - Temperature - Upper Range 9- 83 kHz, Wide Beam Hollow Fish Symbol (Dual Beam Units only) PiranhaMAX™ Sonar Technology Single Beam Sonar Dual Beam Sonar The Menu System Light PiranhaMAX™Portables Sensitivity Depth Range Zoom Chart Speed Fish Alarm Large fish only Large/Medium fish only All fish Filter SetUp Menu Contrast • Battery Alarm Fish ID+TM Dual Beam Single Beam NOTE: Bottom Black View is not available on color models Battery Alarm (SetUp Menu) Language (SetUp Menu) (Setting Saved in Memory, International only) Units (SetUp Menu) Maintenance How to Remove Water from the Portable Case Troubleshooting 1.Nothing happens when I turn the unit on 2.There is no transducer detected 3.There is no bottom readingvisible on the display 5.The unit comes on before I press the POWER-MENUkey, and won’t turn off 6.I get gaps in the reading at certainspeeds 7.The display begins to fade out. Images are not as sharp as normal 8.The display shows many black dots at high sensitivitysettings International Purchases Humminbird®1-YearLimited Warranty This warranty does not apply to a product that has been: •Improperly installed; •Damaged or has failed because of an accident or abnormal operation; •Repaired or modified by entities other than Humminbird® PLEASE DO NOT RETURN THIS PRODUCT TO STORE FOR SERVICE Returning Your Unit for Service NOTE: Please do not return your Humminbird® to the store for service NOTE: For IN-WARRANTYservice, complete the following steps: •Include a brief written description of the problem Specifications 600 ft (185 m) – (PMAX150/160) 800 ft (250 m) – (PMAX190c) 800 Watts (PTP) – (PMAX150/160) 1600 Watts (PTP) – (PMAX190c) Page in any of the followingways: By Telephone By e-mail cservice@johnsonoutdoors.com For direct shipping, our address is: