W a r n i n g

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1.Use this unit only in a manner intended by the manufacturer. If you have questions, contact the manufacturer.

2.Before servicing or cleaning the unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

3.Installation work and electrical wiring must be done by quali- fied person(s) in accordance with all applicable codes and standards, including fire-rated construction.

4.Sufficient air is needed for proper combustion and exhausting of gasses through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufac- turer’s guideline and safety standards,such as those published by the National Fire Prevention Association (NFPA), and the

American Society for Heating, Refrigeration and Air-Conditioning Engineers (ASHRAE), and the local code authorities.

5.When cutting or drilling into wall(s) or ceiling, do not damage electrical wiring or other hidden utilities.

6.Ducted fans must always be vented to the outdoors.

7.If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and be connected to a GFCI (Ground Fault Circuit Interrupter) – protected branch circuit.

8.Never place a switch where it can be reached from a tub or shower.

9.Install fan at least 5 feet (1.52 m) above the floor.

10.This unit must be grounded.

11.Unit must not be installed in a ceiling thermally insulated to a value greater than R40.

C A U T I O N

1.For general ventilating use only. Do not use to exhaust hazard- ous or explosive materials and vapors.

2.To avoid motor bearing damage and noisy/unbalanced impellers, keep drywall spray, construction dust, etc. off power unit.

3.DO NOT install this product in a wall. This product is designed for installation in ceilings up to a 12/12 pitch (45 degrees). Ductwork must point upward.

4.Please read specification label on product for further information and requirements.

W a r n i n g

DISCONNECT ELECTRIC

POWER SUPPLY

AND LOCK OUT

SERVICE PANEL BEFORE

SERVICING UNIT

PREVENTATIVE MAINTENANCE

A clean fan provides better service. Disconnect the power supply and clean the fan as listed below.

TO CLEAN GRILLE: Use a mild detergent, such as dishwashing liquid, and a soft cloth. DO NOT use abrasive cloths, steel wool pads or scouring powders.

TO CLEAN FAN ASSEMBLY: Unplug motor cord from receptacle. To remove motor plate, find the single tab on the motor plate (located next to the receptacle). Push up rear motor plate tab while pushing out on the side of the housing or insert a screwdriver into the slot in the housing (next to tab) and twist screwdriver. Gently vacuum fan, motor and interior of housing.

METAL AND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED IN WATER.

MAINTENANCE

The motor is permanently lubricated and never needs oiling. If the motor bearings are making excessive or unusual noises, replace the motor with the exact service motor. You should replace the impeller at the same time.

COOKING AREA

 

Do Not Install Above

 

Or Inside This Area

 

45°

45°

 

 

Cooking

Floor

 

 

 

Equipment

 

41953-01 02/15/2008

023_41953_EngS_2-15-08.indd 2

2/16/08 12:25:27 PM

Page 1 Page 3
Page 2
Image 2
Hunter Fan 41953-01 manual R n i n g
Page 1 Page 3

41953-01 specifications

The Hunter Fan 41953-01 is a stylish and functional ceiling fan designed to enhance both the aesthetics and comfort of any room. Perfectly suited for living rooms, bedrooms, or covered patios, this fan combines modern technology with classic design elements, ensuring it fits seamlessly into various interior decors.

One of the standout features of the Hunter Fan 41953-01 is its versatile design. The fan is available in a range of elegant finishes, allowing homeowners to select a look that complements their decor. The blades are crafted from high-quality materials, ensuring durability and longevity while providing optimal airflow. The aerodynamic blade design maximizes efficiency, allowing the fan to create a powerful yet quiet breeze.

The Hunter Fan 41953-01 is equipped with a range of intelligent technologies that enhance its performance. One of the most notable is the WhisperWind motor, which offers exceptional airflow while maintaining a whisper-quiet operation. This technology is particularly valuable for those who want to enjoy a cooling breeze without the distracting noise that traditional fans can produce.

Additionally, the fan features a reversible motor, allowing it to rotate in both directions. This capability is perfect for seasonal use, as it enables the fan to create a cooling downdraft during the summer months and a cozy updraft during the winter. This dual functionality promotes energy efficiency, helping to reduce heating and cooling costs year-round.

Installation of the Hunter Fan 41953-01 is made easy with the included instructional guide and mounting kit. The fan is designed for straightforward assembly, making it accessible for those who may not have extensive DIY experience. Furthermore, the fan can be paired with a variety of light kits, allowing users to customize their lighting options while adding to the fan's overall aesthetic appeal.

In addition to its impressive performance and design, the Hunter Fan 41953-01 is backed by a reputable brand known for its commitment to quality and customer satisfaction. The fan comes with a limited lifetime warranty, ensuring peace of mind and long-lasting enjoyment.

Overall, the Hunter Fan 41953-01 is a perfect blend of style, technology, and efficiency. With its attractive design, innovative features, and reliable operation, it stands out as an excellent choice for anyone looking to improve their home’s comfort and visual appeal.
Top Page Image Contents