APPLICATION OF SOAP DEGREASER

1.Apply the solution to a DRY work surface. NOTE:

WETTING THE SURFACE FIRST IS NOT RECOMMENDED, AS IT DILUTES THE DETERGENT AND REDUCES ITS CLEANING ABILITY. On a vertical surface, apply horizontally from side to side starting from the bottom to avoid streaking.

2.Allow chemical to remain on the surface for a short time before rinsing

CAUTION: Damage may occur to painted surface if chemical is allowed to dry on the surface. Wash and rinse a small

CAUTION section at a time. Avoid working on hot

surfaces or in direct sunlight.

3.Rinse with clean water under high pressure. On a vertical surface, first rinse from the bottom up, then rinse from the top down. Hold nozzle 6 to 8 inches from the work surface at a 45° angle using the flat spray as a peeling tool rather than a scrub brush.

NOTE: Insure that the chemical injection system is completely clean prior to switching from one chemical to another.

APPLICATION OF LIQUID VEHICLE WAX

1.Immediately after cleaning, apply Pressure Washer Liquid Vehicle Wax using low pressure. Pour wax into chemical solution reservoir.

2.Apply the wax sparingly in an even layer. Apply to wet surfaces from the bottom up for even distribution and to avoid streaking.

3.Rinse off the surplus wax. NOTE – IF SURPLUS WAX IS NOT REMOVED, A HAZY FINISH MAY RESULT.

4.Wipe dry to reduce water spotting.

4.7END OF OPERATION

When you have completed use of the chemical injection system, continue to run in low pressure position and flush clean water through the chemical tank until it is thoroughly cleaned.

NOTE: Failure to clean properly will cause the injection system to become clogged and inoperable.

λStop the unit by pressing to ON/OFF button

λDisconnect electrical plug

λTurn off water and depressurize unit by squeezing trigger.

APPLICATION DE SAVON DÉGRAISSANT

1.Appliquer la solution nettoyante sur une surface de travail SÈCHE. REMARQUE : IL EST DÉCONSEILLÉ DE MOUILLER LES SURFACES, CAR LE DÉTERGENT SERAIT ALORS DILUÉ ET SON EFFET DIMINUÉ. Dans le cas d’une surface verticale, appliquer le savon horizontalement d'un côté à l'autre en commençant par le bas afin d’éviter les rayures.

2.Avant de rincer, laisser le produit chimique sur la surface pendant un bref laps de temps.

ATTENTION : Si on laisse sécher le savon, les surfaces vernies ou peintes peuvent être endommagées. Laver et rincer

ATTENTIONune petite section à la fois. Éviter de travailler sur des surfaces chaudes ou sous la lumière directe du soleil.

3.Rincer à l’eau propre à haute pression. Sur les surfaces verticales, rincer de bas en haut et inversement. Tenir le gicleur à 15-20 cm (6-8 po) de la surface à traiter et à un angle de 45°, en utilisant le jet turbo comme outil de raclage et non comme une brosse métallique.

REMARQUE : Assurez-vous que le système d’injection chimique est entièrement propre avant de passer d’un produit à un autre.

APPLICATION DE CIRE LIQUIDE POUR VÉHICULES

1.Immédiatement après le lavage, appliquer la cire liquide pour véhicules, en utilisant la basse pression. Versez de la cire dans le réservoir de produit chimique.

2.Appliquer la cire avec parcimonie en une couche uniforme. Appliquer, sur les surfaces mouillées, du bas vers le haut afin d’obtenir une distribution uniforme et d’éviter les rayures.

3.Éliminer l’excédent de cire. REMARQUE : SI L‘EXCÉDENT DE CIRE N‘EST PAS ÉLIMINÉ, LE RÉSULTAT OBTENU EST OPAQUE.

4.Sécher en essuyant afin de réduire les traces d’eau.

4.7FIN DE L'UTILISATION

Lorsque l’utilisation du système d’injection de produit chimique est terminée, faire fonctionner l’appareil, toujours à basse pression, et faire passer de l’eau propre dans le tuyau pour un nettoyage complet.

REMARQUE : À défaut de faire un nettoyage complet, le système d'injection s'obstruera et deviendra inutilisable.

λArrêter l’appareil en appuyant sur la touche mar- che/arrêt

λDébrancher la prise électrique

λFermer l’eau et dépressuriser l’appareil en appuyant sur la gâchette

19

Page 18 Page 20
Page 19
Image 19
Husky 1650 PSL Application of Soap Degreaser, Application of Liquid Vehicle WAX, END of Operation, FIN DE Lutilisation
Page 18 Page 20

1650 PSL specifications

The Husky 1650 PSL is a sophisticated and versatile injection molding machine specifically designed for high-performance applications across various industries. Renowned for its reliability and efficiency, the Husky 1650 PSL stands out as an optimized solution for companies requiring precision in their production lines.

One of the most notable features of the Husky 1650 PSL is its high-speed injection capabilities. This machine utilizes advanced hydraulics to deliver rapid injection cycles, resulting in shorter production times and enhanced productivity. The machine boasts a robust clamping force of 1650 tons, providing the necessary support for processing larger and more complex molds with precision.

In terms of technology, the Husky 1650 PSL incorporates a user-friendly, programmable control system that allows for real-time monitoring and adjustments. This feature makes it easy for operators to optimize the molding process based on specific requirements. Additionally, the machine is equipped with state-of-the-art servo technology, which significantly improves energy efficiency while reducing cycle times. This not only leads to lower operational costs but also enhances overall sustainability.

The machine's design includes a wide range of customizable options, allowing manufacturers to tailor the Husky 1650 PSL to their specific needs. The modular design supports integration with various auxiliary equipment, such as robots and conveyors, fostering a streamlined manufacturing process. Moreover, the machine's advanced cooling and heating systems ensure consistent temperatures for stable material processing, directly contributing to the quality of the final products.

Another standout feature of the Husky 1650 PSL is its compatibility with a variety of thermoplastic materials, making it an ideal choice for producing complex parts in industries ranging from automotive to consumer goods. The machine's versatility is further enhanced by its ability to work with multiple cavity molds, contributing to higher output while maintaining tight tolerances.

In conclusion, the Husky 1650 PSL is a powerful injection molding machine that combines high performance, advanced technology, and customization capabilities to meet the rigorous demands of modern manufacturing. Its innovative features not only improve production efficiency but also ensure the consistent quality of molded products, making it a valuable asset in any production facility.
Top Page Image Contents