Husky 1650 PSL warranty Safety and Operation Rules

Models: 1650 PSL

1 32
Download 32 pages 12.17 Kb
Page 8
Image 8

1.0 SAFETY AND OPERATION RULES

Safety precautions are essential when any mechanical equipment is involved. These precautions are necessary when using, storing, and servicing mechanical equipment. Using this equipment with the respect and caution demanded will considerably lessen the possibilities of personal injury. If safety precautions are overlooked or ignored, personal injury or property damage may occur.

The following symbols shown below are used extensively throughout this manual. Always heed these precautions, as they are essential when using any mechanical equipment.

This warning symbol identifies specific instructions or procedures which if not correctly followed could result in perso-

WARNING nal injury or death.

This caution symbol identifies specific instructions or procedures which, if not strictly observed, could result in damage

CAUTION to, or destruction of equipment.

This unit was designed for specific applications. It should not be modified and/or used for any application other than that which it was designed.

When using this product basic precautions should always be followed, including the

WARNING following:.

1.Read this manual carefully - know your equipment. Consider the applications, limitations, and the potential hazards specific to your unit.

2.This product shall only be connected to a power supply receptacle protected by a ground-fault- circuit-interrupter.

3.Do not touch plug or outlet with wet hands.

4.Avoid accidental starts. Move switch on unit to “OFF” position before connecting or disconnecting cord to electrical outlets.

5.Water spray must never be directed towards any electric wiring or directly towards the pressure washer machine itself or fatal electric shock may occur.

6.Never carry your pressure washer by the cord. Do not pull on the cord to disconnect from the outlet.

7.To prevent damage, the cord should not be crushed, placed next to sharp objects or near a heat source.

1.0 CONSIGNES D‘UTILISATION ET DE SÉCURITÉ

Il est essentiel de prendre des mesures de sécurité lors de l’utilisation de tout appareil mécanique. De telles mesures sont nécessaires pendant l’utilisation, le remisage et l’entretien de l’appareil mécanique. En utilisant l’appareil avec attention et dans le respect des consignes, les possibilités de blessures diminuent considérablement. Si ces mesures de sécurité sont ignorées ou ne sont pas mises en pratique, l’utilisateur risque de se blesser ou d’endommager l’appareil. Les symboles décrits ci-dessous sont largement utilisés dans le présent manuel. Tenez toujours compte des mesures de sécurité qui y sont associées, car elles sont essentielles lors de l’utilisation de tout appareil mécanique.

 

Ce symbole identifie des instructions ou

 

des procédures spécifiques qui, si elles

ATTENTION

ne sont pas appliquées, peuvent causer

de graves blessures ou entraîner la mort.

 

Ce symbole identifie des instructions ou

 

des procédures spécifiques qui, si elles

 

ne sont pas scrupuleusement observées,

IMPORTANT

peuvent endommager ou même détruire

 

l’appareil.

Cette unité a été conçue pour des applications spécifiques. Elle ne doit pas être modifiée ou utilisée pour des applications différentes de celle pour laquelle elle a été conçue.

Lors de l’utilisation de l’appareil, des précautions de base doivent être

ATTENTION observées, et notamment :

1.Lire attentivement le présent manuel pour une meilleure connaissance de l’appareil, au niveau de ses applications, ses limites et des risques potentiels.

2.Ce produit ne peut être branché que sur une prise d’alimentation protégée par un dispositif d’interruption de circuit pour défaut lié à la terre.

3.Ne pas toucher la prise avec les mains mouillées.

4.Éviter les démarrages accidentels. Mettre l’interrupteur en position ARRÊT, avant de brancher ou de débrancher le câble électrique à une prise.

5.Ne jamais diriger le jet d’eau sur des installations électriques ou sur le nettoyeur à pression afin d’éviter une décharge électrique mortelle.

6.Ne pas déplacer le nettoyeur à pression en tirant sur le câble. Ne pas tirer le câble pour débrancher l’appareil de la prise.

7.Afin d’éviter des dommages, le câble ne doit pas être écrasé ou placé près d’objets tranchants ou de sources de chaleur.

8

Page 8
Image 8
Husky 1650 PSL warranty Safety and Operation Rules

1650 PSL specifications

The Husky 1650 PSL is a sophisticated and versatile injection molding machine specifically designed for high-performance applications across various industries. Renowned for its reliability and efficiency, the Husky 1650 PSL stands out as an optimized solution for companies requiring precision in their production lines.

One of the most notable features of the Husky 1650 PSL is its high-speed injection capabilities. This machine utilizes advanced hydraulics to deliver rapid injection cycles, resulting in shorter production times and enhanced productivity. The machine boasts a robust clamping force of 1650 tons, providing the necessary support for processing larger and more complex molds with precision.

In terms of technology, the Husky 1650 PSL incorporates a user-friendly, programmable control system that allows for real-time monitoring and adjustments. This feature makes it easy for operators to optimize the molding process based on specific requirements. Additionally, the machine is equipped with state-of-the-art servo technology, which significantly improves energy efficiency while reducing cycle times. This not only leads to lower operational costs but also enhances overall sustainability.

The machine's design includes a wide range of customizable options, allowing manufacturers to tailor the Husky 1650 PSL to their specific needs. The modular design supports integration with various auxiliary equipment, such as robots and conveyors, fostering a streamlined manufacturing process. Moreover, the machine's advanced cooling and heating systems ensure consistent temperatures for stable material processing, directly contributing to the quality of the final products.

Another standout feature of the Husky 1650 PSL is its compatibility with a variety of thermoplastic materials, making it an ideal choice for producing complex parts in industries ranging from automotive to consumer goods. The machine's versatility is further enhanced by its ability to work with multiple cavity molds, contributing to higher output while maintaining tight tolerances.

In conclusion, the Husky 1650 PSL is a powerful injection molding machine that combines high performance, advanced technology, and customization capabilities to meet the rigorous demands of modern manufacturing. Its innovative features not only improve production efficiency but also ensure the consistent quality of molded products, making it a valuable asset in any production facility.