Auger Assembly 30 LH, Auger Assembly 30 RH | Husqvarna 1130SB-LS

REPAIR PARTS

AUGER HOUSING / IMPELLER ASSEMBLY

SNOW THROWER - MODEL NO. 1130SB-LS (96193002900), PRODUCT NO. 961 93 00-29

2

1

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	532 42 17-26	AUGER ASSEMBLY 30 LH
2	532 42 17-27	AUGER ASSEMBLY 30 RH

01.07.016-A

2

	3
		1
3
	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
	1	532 40 78-34	SKID PLATE
	2	872 27 05-06	CARRIAGE BOLT 5/16−18 X .750
01.11.002-A	3	532 75 11-53	NUT 5/16−18

2	1

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

23

Image 23

Husqvarna 1130SB-LS owner manual Auger Assembly 30 LH, Auger Assembly 30 RH, Skid Plate

Contents

1130SB-LS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in Carton Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Ignition KEY OperationKnow Your Snow Thrower Primer Recoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See Fig Before Starting the Engine If Recoil Starter has Frozen To Start EngineBefore Stopping Lubrication MaintenanceGeneral Recommendations Before Each USE Engine Cleaning Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute Deflector To Replace Belts See Fig Other Storage Troubleshooting Auger Housing / Impeller Assembly Repair Parts KEY Part Description Auger Ball Bearing Skid Plate Auger Assembly 30 LHAuger Assembly 30 RH 01.16.001-A 532 42 17-28 Shield Retainer Strap Control Panel / Discharge ChuteKnob Black POP Rivet Rotator Pivot Bracket 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator Head Handles POP Rivet 1/8 01.05.006-A Repair Parts Bulb Grip Switch532 42 14-48 Headlight Bezel Gray 532 17 86-66 Halogen Headlight Drive HEX Shaft 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly 532 19 77-63 Drive Plate Weldment 532 19 95-09 Rubber Wheel Plate 532 40 61-09 Control Shaft AssemblyAssembly 532 18 00-82 Intermediate Gear Clik PIN Axle ShaftRoll PIN 3/16 Gear Axle Lobe CoverWheel Lobe Clutch Slide Bottom PAN Frame Impeller Belt Chassis / Engine / PulleysPulley Wheels Retainer PIN Power Cord532 03 50-62 Safety Ignition KEY BAG of Parts 532 18 37-30 DECAL, Remote Deflector DECAL, Husq 532 18 10-35 DECAL, DANGER, DeflectorDECAL, Husq Service Notes Service Notes Warranty Statement