Rotator Head, Rotator Pivot Bracket | Husqvarna 1130SB-LS instruction

REPAIR PARTS

CONTROL PANEL / DISCHARGE CHUTE

SNOW THROWER - MODEL NO. 1130SB-LS (96193002900), PRODUCT NO. 961 93 00-29

		*6
KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1532 42 11-60 LEVER/CABLE ROTATOR ASSEMBLY GRAY

2817 50 10-10 SCREW 10−24 X .625

*3	532 42 06-78	ROTATOR HEAD
*4	532 42 11-61	ROTATOR PIVOT BRACKET
*5	532 42 06-75	PULLEY PIVOT
*6	532 42 11-62	CABLE ASSEMBLY GRAY

*4	01.09.008-B	*5

NOTES:

1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 26

Image 26

Husqvarna 1130SB-LS 532 42 11-60 LEVER/CABLE Rotator Assembly Gray, Rotator Head, Rotator Pivot Bracket, Pulley Pivot

Contents

1130SB-LS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEY Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engine HOW to USE Your Snow Thrower Stopping To Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See Fig Before Starting the Engine If Recoil Starter has Frozen To Start EngineBefore Stopping Before Each USE MaintenanceGeneral Recommendations Lubrication Cleaning Engine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Storage Other Troubleshooting Repair Parts Auger Housing / Impeller Assembly KEY Part Description Auger Ball Bearing Skid Plate Auger Assembly 30 LHAuger Assembly 30 RH 01.16.001-A POP Rivet Control Panel / Discharge ChuteKnob Black 532 42 17-28 Shield Retainer Strap Rotator Head 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator Pivot Bracket Handles POP Rivet 1/8 01.05.006-A Repair Parts 532 17 86-66 Halogen Headlight Grip Switch532 42 14-48 Headlight Bezel Gray Bulb Drive 532 19 77-63 Drive Plate Weldment 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly HEX Shaft 532 18 00-82 Intermediate Gear 532 40 61-09 Control Shaft AssemblyAssembly 532 19 95-09 Rubber Wheel Plate Gear Axle ShaftRoll PIN 3/16 Clik PIN Clutch Slide CoverWheel Lobe Axle Lobe Frame Bottom PAN Impeller Belt Chassis / Engine / PulleysPulley Wheels BAG of Parts Power Cord532 03 50-62 Safety Ignition KEY Retainer PIN 532 18 37-30 DECAL, Remote Deflector DECAL, Husq 532 18 10-35 DECAL, DANGER, DeflectorDECAL, Husq Service Notes Service Notes Warranty Statement

Husqvarna 1130SB-LS 532 42 11-60 LEVER/CABLE Rotator Assembly Gray, Rotator Head, Pulley Pivot

Models: 1130SB-LS

REPAIR PARTS

CONTROL PANEL / DISCHARGE CHUTE

SNOW THROWER - MODEL NO. 1130SB-LS (96193002900), PRODUCT NO. 961 93 00-29

KEY

1532 42 11-60 LEVER/CABLE ROTATOR ASSEMBLY GRAY

ROTATOR HEAD

ROTATOR PIVOT BRACKET

PULLEY PIVOT

CABLE ASSEMBLY GRAY