Manuals / Husqvarna / Lawn and Garden / Chainsaw

Husqvarna 1153183-26 manual Needle bearing lubrication, Adjustment of the oil pump, Cooling system

Models: 1153183-26

1 44

Download 44 pages 49.02 Kb

Page 35

Needle bearing lubrication

MAINTENANCE

Needle bearing lubrication

The clutch drum is ﬁtted with one of the following drive sprockets:

•A Spur sprocket (the chain sprocket is welded on the drum) •B Rim sprocket (replaceable)

•Both versions have a needle bearing on the drive shaft, which has to be greased regularly (once a week).

NOTE! Use a high-quality bearing grease or engine oil.

Adjustment of the oil pump

The oil pump is adjustable. Adjustments are made by turning the screw using a screwdriver or combination spanner. The machine is supplied from the factory set to 1 turn open. Turning the screw clockwise will reduce the oil ﬂow and turning the screw anti-clockwise will increase the oil ﬂow.

	!	WARNING! The engine must not be
	!	running when making adjustments.
		running when making adjustments.

Recommended settings:

Bar 24"-28": 0 turns from the closed position.

Bar 28"-34": 3/4 turns from the closed position.

Bar 34"-42": 1 1/2 turns from the closed position.

Bar 42" and longer: 1 3/4 turns from the closed position.

These recommendations apply to Husqvarna’s chain oil, for other chain oils increase the oil ﬂow by one step.

Cooling system

To keep the working temperature as low as possible the machine is equipped with a cooling system.

The cooling system consists of:

1Air intake on the starter.

2 Air guide plate.

3 Fins on the ﬂywheel.

4 Cooling ﬁns on the cylinder.

5 Cylinder cover (directs cold air over the cylinder).

Clean the cooling system with a brush once a week, more often in demanding conditions. A dirty or blocked cooling system results in the machine overheating which causes damage to the piston and cylinder.

English – 35

Image 35

Husqvarna 1153183-26 manual Needle bearing lubrication, Adjustment of the oil pump, Cooling system, Maintenance

Contents

English 3120XPOperator′s manual Symbols in the operator’s manual KEY TO SYMBOLSSymbols on the machine CONTENTS CONTENTSContents KEY TO SYMBOLSDear Customer INTRODUCTIONWhat is what on the chain saw? WHAT IS WHAT?Always use common sense GENERAL SAFETY PRECAUTIONSBefore using a new chain saw WARNING! Faulty cutting equipment orWARNING! Most chain saw accidents Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guardGENERAL SAFETY PRECAUTIONS Will my hand always activate the chain brake during a kickback?Vibration damping system Throttle lockoutChain catcher Right hand guardGeneral rules Stop switchCutting equipment Mufﬂersaw chain can cause extremely serious injuries Sharpening your chain and adjusting depth gauge settingChain WARNING! Any contact with a rotatingWARNING! Departure from the sharpening instructions considerably min 4 mm 5/32 General advice on adjusting depth gauge settingincreased if the depth gauge setting is Adjustment of depth gauge settingand cause serious or even fatal injury Tensioning the chainLubricating cutting equipment WARNING! A slack chain may jump offChecking wear on cutting equipment Checking chain lubricationChain drive sprocket Needle bearing lubricationWARNING! Most chain saw accidents happen when the chain touches the operatorGENERAL SAFETY PRECAUTIONS working with the chain ASSEMBLYFitting the bar and chain WARNING! Always wear gloves, whenPetrol adequate ventilation when handling fuelFUEL HANDLING FuelExtra chain oil Fuel safetyprecautions, will lessen the risk of ﬁre FuellingFUEL HANDLING Transport and storageLong-term storage Warm engine STARTING AND STOPPINGStarting and stopping Cold engineSTARTING AND STOPPING StoppingGeneral working instructions Basic safety rulesWORKING TECHNIQUES Before useWORKING TECHNIQUES Terms Basic cutting techniqueWARNING! Never use a chain saw by GeneralWORKING TECHNIQUES Tree felling techniqueSafe distance Felling directionDirectional cuts Clearing the trunk and preparing your retreatFelling cut Felling WARNING! Unless you have specialCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a ”trapped tree”Limbing WARNING! A majority of kickback How to avoid kickbackWhat is kickback? WARNING! Kickback can happen veryFine adjustment MAINTENANCEFunction, Basic settings, Fine adjustment Basic settings and running inHigh speed jet H Checking, maintaining and servicing chain saw safety equipmentCorrectly adjusted carburettor When the bar hits the stump the brake should be appliedChain catcher Checking the brake triggerMAINTENANCE Throttle lockoutChanging a broken or worn starter cord WARNING! When the recoil spring isMufﬂer StarterMAINTENANCE Tensioning the recoil springChanging a broken recoil spring Fitting the starterMAINTENANCE Air ﬁlterSpark plug Lubricating the bar tip sprocketCooling system Adjustment of the oil pumprunning when making adjustments Needle bearing lubricationMonthly maintenance Maintenance scheduleDaily maintenance Weekly maintenance3120XP TECHNICAL DATATechnical data WeightPitch, inch Bar and chain combinationsSaw chain ﬁling and ﬁle gauges Length, inch0404/09/2119 EC-declaration of conformityApplies to Europe only EN ISO 12100-22003, CISPR 122005, EN ISOPage Page Page Page ´z+U2@¶6G¨ ´z+U2@¶6G¨ Original instructions