Fitting the transport guard, Standard harness | Husqvarna 143R-II

Fitting the transport guard

ASSEMBLY

•Insert the locking pin (C) in the hole to lock the shaft.

•Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation.

H

H

•To dismantle, follow the instructions in the reverse order.

Fitting the transport guard

1Insert the blade in the transport guard (A).

2Snap the two fasteners (B) into the slots (C) to secure the transport guard.

Adjusting the harness and clearing saw

WARNING! When using a clearing saw it

! must always be hooked securely to the harness. Otherwise you will be unable to control the clearing saw safely and this can result in injury to yourself or others. Never use a harness with a defective quick release.

Put on the harness and hang the machine from the support hook. Now make a ﬁnal adjustment so that the machine is in a comfortable working position when it hangs from the harness. Tighten the screws.

Standard harness

Quick release

At the front is an easily accessible, quick release. Use this if the engine catches ﬁre or in any other emergency situation that requires you to free yourself from the machine and harness.

Spreading the load on your shoulders

A well-adjusted harness and machine makes work much easier. Adjust the harness for the best working position. Tension the side straps so that the weight is evenly distributed across both shoulders.

Correct height

Adjust the shoulder strap so that the cutting attachment is parallel to the ground.

English – 15

Image 15

Husqvarna 143R-II Fitting the transport guard, Adjusting the harness and clearing saw, Standard harness, Correct height

Contents

Page ensure, while working, that no KEY TO SYMBOLSSymbols The operator of the machine must CONTENTS CONTENTSContents KEY TO SYMBOLS INTRODUCTION What is what on the brushcutter? WHAT IS WHAT? WARNING! The ignition system of this GENERAL SAFETY PRECAUTIONSWARNING! Listen out for warning signals Personal protective equipment Machine′s safety equipment Throttle lockoutWARNING! Never use a machine with WARNING! Never use a cutting Stop switchCutting attachment guard Vibration damping system WARNING! The inside of the mufﬂer Quick releaseMufﬂer Locking nut Sharpening grass cutters and grass blades WARNING! Using an incorrect cuttingCutting equipment Cutting equipment Trimmer head Assembling the handlebar and throttle ASSEMBLYConnecting throttle cable and stop switch wires Fitting the main body 1-2mm Fitting blades and trimmer heads H L M C BA AM L Fitting the guard extensionFitting the trimmer guard and trimmer head G E F D B C Standard harness Adjusting the harness and clearing sawWARNING! When using a clearing saw it Fitting the transport guard Fuel Fuel safetyWARNING! Take care when handling fuel FUEL HANDLING WARNING! Taking the following precautions, will lessen the risk of ﬁreFuelling Mixing Starting STARTING AND STOPPINGCheck before starting Starting and stopping WARNING! When the engine is started Stoppingstarter cord around your hand WARNING! Neither the operator of the Basic safety rulesWORKING TECHNIQUES General working instructions WARNING! Sometimes branches or Grass clearing using a grass bladeBasic working techniques Grass trimming with a trimmer head Sweeping Cutting Mufﬂer MAINTENANCEAdjusting the idle speed T Carburettor Bevel gear Cleaning the air ﬁlterAir ﬁlter Fuel ﬁlter Daily Maintenance scheduleMaintenance maintenance Weight TECHNICAL DATATechnical data Technical data Type Approved accessoriesEC-declarationof conformity Applies to Europe onlyPage 2,4-2,7 mm 8,5 m 28 10 cm 4,2 mClic 15 cm 2,4-2,7mm 095-.1064,25 m 8,5 m 28 10 cm 4,3 m T35, T35x T45, T45x 10 m 32 10 cm 4,3 m2,7-3,3 mm C 15 cm T55xA 2,7 - 4,0 mm B 8 m / 26’ 12 cm Trimmy SII095-.130 7,0 m