TECHNICAL DATA
| 261 |
Engine |
|
Cylinder volume, cu.in/cm3 | 3,7/61,5 |
Cylinder bore, inch/mm | 1,89/48 |
Stroke, inch/mm | 1,34/34 |
Idle speed, rpm | 2 700 |
Power, kW/ rpm | 2,9/ 9 600 |
Ignition system |
|
Manufacture | Electrolux |
Type of ignition system | ET |
Spark plug | Champion RCJ 7Y |
Electrode gap, inch/mm | 0,020/0,5 |
Fuel and lubrication |
|
system |
|
Manufacturer | Walbro |
Carburetor type | HDA144 |
Fuel capacity, US pint/litre | 1,2/0,6 |
Oil pump capacity at |
|
8 500 rpm, ml/min | |
Oil capacity, US pint/litre | 0,6/0,3 |
Type of oil pump | Automatic |
Weight |
|
Without bar and chain, Lbs/kg | 12,7/5,8 |
Chain/bar |
|
Recommended bar lengths, |
|
inches/cm | |
Usable cutting length |
|
inches/cm | |
Chain speed at max. |
|
power, m/sec | 18,5 |
Pitch, inches | 0,325"/ 3/8" |
Thickness of drive link, | 0,058"/1,5 and 0,050"/1,3 |
inch/mm | |
Number of teeth on drive | 7 |
sprocket |
Recommended original and replacement bar and chain combinations
Following is a list of recommended cutting equipment for the Husqvarna chain saw model 261. The combinations of power head, bar and chain have been investigated in accordance with the kickback and vibration requirements of ANSI B
The guide bar nose radius is determined by either the maximum number of teeth in the nose sprocket or the corresponding maximum nose radius of a solid bar.
The following list is the chain saw manufacturers recommendations. There may be other combinations available, which will also achieve kickback protection.
As we are listing the maximum guide bar nose radius, you may use a guide bar with smaller nose radius than in our list. For guide bars of the same length, all
Low kickback saw chain is a chain which has only met the kickback performance requirements of ANSI B 175.1 safety requirements for gasoline powered chain saws when tested on the representative sample of chain saws below 3.8 cu. in. specified in ANSI B 175.1. We recommend that you as a replacement use the listed chains or "Low kickback saw chains" which are available at your dealer.
Guide bar |
| Saw chain | |
Length | Pitch | Max nose |
|
inch | inch | radius |
|
|
|
|
|
13 | 0,325" | 10T | Husqvarna H30 or Oregon 95VP |
15 | 0,325" | 10T |
|
16 | 0,325" | 10T |
|
18 | 0,325" | 10T |
|
|
|
|
|
15 | 0,325" | 10T | Husqvarna H21/H25/S24 or |
16 | 0,325" | 10T | Oregon 21LP/21VB/34LG |
18 | 0,325" | 10T |
|
20 | 0,325" | 10T |
|
|
|
|
|
16 | 3/8" | 11T | Husqvarna H42/S48 or |
18 | 3/8" | 11T | Oregon 73L/73VL/73LG |
20 | 3/8" | 11T |
|
24 | 3/8" | 11T |
|
|
|
|
|
Note: For the chains above you are free to choose between 0,050" and 0,058" gauge drive link for the corresponding bar, see the table below.
0,058"/1,5mm | – | – | H25,H21 |
| S24 |
| 21VB | 21LP | 34LG | ||
|
|
|
|
|
|
|
|
|
|
|
|
0,050"/1,3mm | H30 | 95VP | – |
| – |
| 20VB | 20LP | 33LG | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
0,058"/1,5mm | H42 | S48 | 73L |
| 73VL | 73LG |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
0,050"/1,3mm | – | – | 72L |
| 72VL | 72LG |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
34«*3®G¦5(¬
– English