To Replace Mower Blade Drive Belt See Fig | Husqvarna 2748 GLS (CA)

SERVICE AND ADJUSTMENTS

B
	A
Tighten adjust nut	Loosen adjust nut
B to raise mower	B to lower mower
02950
Loosen jam nut A first

FIG. 28

NOTE: Each full turn of the adjustment nut will change mower height about 1/8".

•Recheck measurements, adjust if necessary until front tip of blade is 1/8" to 1/2" lower than the rear tip.

•Hold adjustment nut in position with wrench and tighten jam nut securely against adjustment nut.

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 29)

MOWER DRIVE BELT REMOVAL

•Park tractor on a level surface. Engage parking brake.

•Lower attachment lift lever to its lowest position.

•Disengage belt tension rod (K) from lock bracket (L).

CAUTION: Belt tension rod is spring loaded. Have a firm grip on rod and release slowly.

•Remove screws (P) from mandrel covers (Q) and remove covers.

•Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.

•Remove belt from electric clutch pulley (M), both man- drel pulleys (R) and all idler pulleys (S).

MOWER DRIVE BELT INSTALLATION

•Install belt around all mandrel pulleys (R) and around idler pulleys (S) as shown.

•Install belt onto electric clutch pulley (M).

IMPORTANT: Check belt for proper routing in all mower pulley grooves.

•Reassemble mandrel covers (Q). Securely tighten all screws.

•Engage belt tension rod (K) on locking bracket (L).

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.

•Raise attachment lift lever to highest position.

		P
	Q	P
	Q
		M
K		R
K	L
	L	Q
		Q
	R
		S
		R
		FIG. 29
		22

Image 23

Husqvarna 2748 GLS (CA) To Replace Mower Blade Drive Belt See Fig, Mower Drive Belt Removal, Mower Drive Belt Installation

Contents

GLS CA Page II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General Operation IV. Towing ServiceIII. Children Table of Contents To Remove Tractor from Carton AssemblyTools Required for Assembly Unassembled Parts Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL Belts Operation Know Your Tractor To USE Throttle Control D See Fig HOW to USE Your TractorTo SET Parking Brake See Fig Stopping To Operate Mower To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Move Forward and Backward See Fig To Operate on Hills Service REMINDER/HOUR MeterBefore Starting the Engine Reverse Operation System ROS Automatic Transmission Warm UP ADD GasolineTo Start Engine See Fig Purge Transmission Mowing Tips General Recommendations MaintenanceLubrication Chart Tires BatteryTractor Brake Operation Engine Spark Plugs CleaningEngine OIL Filter Muffler To Remove Mower See Fig Service and Adjustments First Install ANTI-SWAY BAR S To Install Mower See Figs Engage belt tension rod K on locking bracket L Turn nut right Turn nut left To raise mower To Level Mower Mower Drive Belt Removal Mower Drive Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Remove Wheel for Repairs See Fig To Replace Motion Drive Belt See FigTo Check Brake Front Wheel TOE-IN/CAMBER To Remove CABLES, Reverse Order To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Attach Jumper Cables To Adjust Carburetor WireTo Adjust Throttle Control Cable To Adjust Choke Control Engine OIL StorageOther Fuel System Troubleshooting Points Engine dies when Tractor Model no GLS 96043005000, Product no 43 Schematic Tractor Model no GLS 96043005000, Product no 43 KEY Part Description Electrical Chassis Tractor Model no GLS 96043005000, Product no 43 Drive Tractor Model no GLS 96043005000, Product no 43 Steering Assembly Spark Arrester KIT Engine Seat Assembly Wheels and Tires Decals Mower Deck Tractor Model no GLS 96043005000, Product no 43 Mower Lift Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation 532 41 88-49 Rev 1 03-31-08 SBW/TH Warranty Statement