Manuals / Brands / Lawn and Garden / Chainsaw / Husqvarna / Lawn and Garden / Chainsaw

Husqvarna 395XP, 395XPG Needle bearing lubrication, Adjustment of the oil pump, Cooling system, Air Injection centrifugal cleaning

1 44

Download 44 pages, 3.63 Mb

MAINTENANCE

English – 37

Needle bearing lubrication

The clutch drum has a needle bearing on the output shaft.

This needle bearing must be lubricated regularly (once a

week). CAUTION! Use a high-quality bearing grease or

engine oil. See instructions under the heading Cutting

equipment.

Adjustment of the oil pump

The oil pump is adjustable. Adjustments are made by

turning the screw using a screwdriver or combination

spanner. The machine is supplied from the factory set to

1 turn open. Turning the screw clockwise will reduce the

oil ﬂow and turning the screw anti-clockwise will increase

the oil ﬂow.

Recommended settings:

These recommendations apply to Husqvarna’s chain oil,

for other chain oils increase the oil ﬂow by one step.

Cooling system

To keep the working temperature as low as possible the

machine is equipped with a cooling system.

The cooling system consists of:

1 Air intake on the starter.

2 Air guide plate.

3 Fins on the ﬂywheel.

4 Cooling ﬁns on the cylinder.

5 Cylinder cover (directs cold air over the cylinder).

Clean the cooling system with a brush once a week, more

often in demanding conditions. A dirty or blocked cooling

system results in the machine overheating which causes

damage to the piston and cylinder.

”Air Injection” centrifugal

cleaning

Centrifugal cleaning means the following: All air to the

carburettor passes through the starter. Dirt and dust is

centrifuged out by the cooling fan.

IMPORTANT! In order to maintain operation of the

centrifugal cleaning system it must be regularly

maintained. Clean the air intake to the starter, the ﬁns on

the ﬂywheel, the space around the ﬂywheel, inlet pipe and

carburettor compartment.

Bar 18"-20": 0 turns from the closed position.

Bar 20"-24": 3/4 turns from the closed position.

Bar 24"-28": 1 1/2 turns from the closed position.

Bar 28" and longer: 1 3/4 turns from the closed position.

!

WARNING! The engine must not be

running when making adjustments.

1

2

5

4

3

Contents

Main 395XP 395XPG KEY T O SYMBOLS Symbols on the mac hine: CONTENTS Contents INTR ODUCTION Dear Customer , WHA T IS WHA T? Bef ore using a new chain saw Impor tant Al ways use common sense ont hand guard Chain brake and fr s safety equipment Page Will my hand always activate the chain brake during a kickback? Will my inertia activated chain brake always activate during kickback in the event of a kickback? Will my chain brake always protect me from injury in the event of a kickback? Throttle trigger lockout Chain catcher Cutting equipment General rules Cutting equipment designed to reduce kickback Sharpening your chain and adjusting depth gauge setting Tensioning the chain Lubricating cutting equipment Page ASSEMBLY Fitting the bar and chain Fitting a spiked bumper FUEL HANDLING Fuel Petrol Two-stroke oil Mixing FUEL HANDLING Fueling Fuel safety Transport and storage Long-term storage STARTING AND STOPPING Starting and stopping A Cold engine Warm engine STARTING AND STOPPING Stopping Before use: General working instructions Basic safety rules , General rules Basic cutting technique Tree felling technique Page Page Freeing a tree that has fallen badly How to avoid kickback What is kickback? Carburettor adjustment Carburettor with movement limiters Function, Basic settings, Fine adjustment Function Basic settings and running in Fine adjustment Carburettor without movement limiters H L Function L Basic settings and running in Fine adjustment Conditions Low speed jet L H Correctly adjusted carburettor Checking, maintaining and servicing chain saw safety equipment Chain brake and front hand guard Throttle trigger lockout Chain catcher Right hand guard Vibration damping system Stop switch Mufer Starter housing Changing a broken or worn starter cord Tensioning the recoil spring Changing a broken recoil spring Fitting the starter Air lter Spark plug Lubricating the bar tip sprocket Needle bearing lubrication Adjustment of the oil pump Cooling system Air Injection centrifugal cleaning Winter use Temperature -5 Fitting the winterising kit Temperature 0 C or colder Maintenance schedule Technical data Guide bar and saw chain combinations Saw chain ling and le gauges EC Declaration of Conformity (Applies to Europe only)