Manuals / Husqvarna / Lawn and Garden / Tiller

Husqvarna 500RTTA owner manual Carburetor, Engine Speed, Throttle Control, Service And Adjustments

Models: 500RTTA

1 28

Download 28 pages 62.18 Kb

Page 16

Image 16

SERVICE AND ADJUSTMENTS

ENGINE

CARBURETOR

The carburetor has been preset at the factory and adjustment should not be necessary. However, engine performance can be affected by differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, contact your nearest authorized service center/department.

•The air ﬁlter must be assembled to the carburetor when running engine.

•Best carburetor adjustment is obtained when fuel tank is 1/4 full.

See the adjustment sectin of your engine manual for further instructions.

ENGINE SPEED

The engine speed has been factory set. Do not attempt to increase engine speed as it may result in personal injury. If you believe the engine is running too fast or too slow, take your tiller to an authorized engine service center for repair and adjustment.

THROTTLE CONTROL

If it becomes necessary to adjust or replace the throttle con- trol, see the adjustment section of your engine manual.

Page 16

Image 16

Husqvarna 500RTTA owner manual Carburetor, Engine Speed, Throttle Control, Service And Adjustments

Contents

500RTTA 917.296250SAFETY RULES MAINTENANCE AND STORAGETRAINING PREPARATIONTABLE OF CONTENTS PRODUCT SPECIFICATIONSCUSTOMER RESPONSIBILITIES 7-10ASSEMBLY TOOLS REQUIRED FOR ASSEMBLYCONTENTS OF HARDWARE PACK OPERATOR’S POSITION See FigUNPACKING CARTON See Fig INSTALL HANDLE See Figs. 3, 4, andASSEMBLY ATTACH CLUTCH CABLE See Fig CONNECT SHIFT ROD See FigREMOVE TILLER FROM CRATE CHECK TIRE PRESSUREREAD THIS OWNERS MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER MEETS ANSI SAFETY REQUIREMENTSOPERATION KNOW YOUR TILLERHOW TO USE YOUR TILLER STOPPING See FigDEPTH STAKE See Fig TINE OPERATION - WITH WHEEL DRIVEBEFORE STARTING ENGINE TURNINGOUTER SIDE SHIELDS See Fig TO TRANSPORTTINE SHEAR PINS TILLING HINTSCULTIVATING OPERATIONMAINTENANCE LUBRICATION CHARTGENERAL RECOMMENDATIONS BEFORE EACH USECLEANING AIR CLEANERENGINE MUFFLERSERVICE AND ADJUSTMENTS TO ADJUST HANDLE HEIGHT See FigTILLER TIRE CARETO REPLACE GROUND DRIVE BELT See Fig GROUND DRIVE BELT ADJUSTMENT See FigSERVICE AND ADJUSTMENTS TINE REPLACEMENT See Figs. 22, 23, and SERVICE AND ADJUSTMENTSCARBURETOR ENGINE SPEEDTHROTTLE CONTROL SERVICE AND ADJUSTMENTSSTORAGE OTHERFUEL SYSTEM ENGINE OILTROUBLESHOOTING POINTS REPAIR PARTS HANDLE ASSEMBLYTILLER - - MODEL NUMBER 500RTTA 917.296250, PRODUCT NUMBER KEY PART NO. NO. DESCRIPTIONMAINFRAME, LEFT SIDE REPAIR PARTSTILLER - - MODEL NUMBER 500RTTA 917.296250, PRODUCT NUMBER 954 PARTMAINFRAME, RIGHT SIDE REPAIR PARTSTILLER - - MODEL NUMBER 500RTTA 917.296250, PRODUCT NUMBER KEY PART NO. NO. DESCRIPTIONREPAIR PARTS TILLER - - MODEL NUMBER 500RTTA 917.296250, PRODUCT NUMBER 954 32TRANSMISSION KEY PART NO. NO. DESCRIPTIONTINE SHIELD REPAIR PARTSTILLER - - MODEL NUMBER 500RTTA 917.296250, PRODUCT NUMBER KEY PART NO. NO. DESCRIPTIONTINE ASSEMBLY REPAIR PARTSTILLER - - MODEL NUMBER 500RTTA 917.296250, PRODUCT NUMBER 954 PARTDECALS REPAIR PARTSTILLER - - MODEL NUMBER 500RTTA 917.296250, PRODUCT NUMBER 954 32 KEY PART NO. NO. DESCRIPTIONWARRANTY STATEMENT SECTION 1 LIMITED WARRANTYSECTION 2 HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY SECTION 3 ITEMS NOT COVERED BY THIS WARRANTYSERVICE NOTES 532 18 60-96 Rev. 2 05.19.03 TR/rad/TR 01960husqvarna