Manuals / Husqvarna / Lawn and Garden / Tiller

Husqvarna 500RTTA TO REPLACE GROUND DRIVE BELT See Fig, GROUND DRIVE BELT ADJUSTMENT See Fig

Models: 500RTTA

1 28

Download 28 pages 62.18 Kb

Page 14

TO REPLACE GROUND DRIVE BELT (See Fig. 21)

SERVICE AND ADJUSTMENTS

TO REPLACE GROUND DRIVE BELT (See Fig. 21)

•Remove belt guard (See “TO REMOVE BELT GUARD” in this section of this manual).

•Remove old belt by slipping off engine pulley ﬁrst then remove from transmission pulley.

•Place new belt in groove of transmission pulley and into engine pulley. BELT MUST BE IN GROOVE ON TOP OF IDLER PULLEY. NOTE POSITION OF BELT TO GUIDES.

•Check belt adjustment as described below.

•Replace belt guard.

•Reposition wheel and replace clevis pin and hairpin clip.

ENGINE

PULLEY

IDLER	TRANSMISSION PULLEY
PULLEY

GROUND DRIVE BELT ADJUSTMENT (See Fig. 21)

For proper belt tension, the extension spring should have about 5/8 inch stretch when drive control bar is in “ENGAGED” position. This tension can be attained as follows:

•Loosen cable clip screw securing the drive control cable.

•Slide cable forward for less tension and rearward for more tension until about 5/8 inch stretch is obtained while the drive control bar is engaged.

•Tighten cable clip screw securely.

CABLE CLIP

SCREW

DRIVE

CONTROL

CABLE

LESS

TENSION

		MORE
5/8"		TENSION

EXTENSION

SPRING

FIG. 21

14

Image 14

Husqvarna 500RTTA TO REPLACE GROUND DRIVE BELT See Fig, GROUND DRIVE BELT ADJUSTMENT See Fig, Service And Adjustments

Contents

500RTTA 917.296250TRAINING SAFETY RULESMAINTENANCE AND STORAGE PREPARATIONCUSTOMER RESPONSIBILITIES TABLE OF CONTENTSPRODUCT SPECIFICATIONS 7-10CONTENTS OF HARDWARE PACK ASSEMBLYTOOLS REQUIRED FOR ASSEMBLY OPERATOR’S POSITION See FigASSEMBLY INSTALL HANDLE See Figs. 3, 4, andUNPACKING CARTON See Fig REMOVE TILLER FROM CRATE ATTACH CLUTCH CABLE See FigCONNECT SHIFT ROD See Fig CHECK TIRE PRESSUREOPERATION READ THIS OWNERS MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLERMEETS ANSI SAFETY REQUIREMENTS KNOW YOUR TILLERDEPTH STAKE See Fig HOW TO USE YOUR TILLERSTOPPING See Fig TINE OPERATION - WITH WHEEL DRIVEOUTER SIDE SHIELDS See Fig BEFORE STARTING ENGINETURNING TO TRANSPORTCULTIVATING TINE SHEAR PINSTILLING HINTS OPERATIONGENERAL RECOMMENDATIONS MAINTENANCELUBRICATION CHART BEFORE EACH USEENGINE CLEANINGAIR CLEANER MUFFLERTILLER SERVICE AND ADJUSTMENTSTO ADJUST HANDLE HEIGHT See Fig TIRE CARESERVICE AND ADJUSTMENTS GROUND DRIVE BELT ADJUSTMENT See FigTO REPLACE GROUND DRIVE BELT See Fig TINE REPLACEMENT See Figs. 22, 23, and SERVICE AND ADJUSTMENTSTHROTTLE CONTROL CARBURETORENGINE SPEED SERVICE AND ADJUSTMENTSFUEL SYSTEM STORAGEOTHER ENGINE OILTROUBLESHOOTING POINTS TILLER - - MODEL NUMBER 500RTTA 917.296250, PRODUCT NUMBER REPAIR PARTSHANDLE ASSEMBLY KEY PART NO. NO. DESCRIPTIONTILLER - - MODEL NUMBER 500RTTA 917.296250, PRODUCT NUMBER 954 MAINFRAME, LEFT SIDEREPAIR PARTS PARTTILLER - - MODEL NUMBER 500RTTA 917.296250, PRODUCT NUMBER MAINFRAME, RIGHT SIDEREPAIR PARTS KEY PART NO. NO. DESCRIPTIONTRANSMISSION REPAIR PARTSTILLER - - MODEL NUMBER 500RTTA 917.296250, PRODUCT NUMBER 954 32 KEY PART NO. NO. DESCRIPTIONTILLER - - MODEL NUMBER 500RTTA 917.296250, PRODUCT NUMBER TINE SHIELDREPAIR PARTS KEY PART NO. NO. DESCRIPTIONTILLER - - MODEL NUMBER 500RTTA 917.296250, PRODUCT NUMBER 954 TINE ASSEMBLYREPAIR PARTS PARTTILLER - - MODEL NUMBER 500RTTA 917.296250, PRODUCT NUMBER 954 32 DECALSREPAIR PARTS KEY PART NO. NO. DESCRIPTIONSECTION 2 HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY WARRANTY STATEMENTSECTION 1 LIMITED WARRANTY SECTION 3 ITEMS NOT COVERED BY THIS WARRANTYSERVICE NOTES 532 18 60-96 Rev. 2 05.19.03 TR/rad/TR 01960husqvarna