Manuals / Husqvarna / Lawn and Garden / Snow Blower

Husqvarna 5021 R, 5021 E manual Handle Assembly, Ref No, Description, Footnotes

Models: 5021 E 5021 R

1 42

Page 36

Handle Assembly

REF NO	PART NO.	DESCRIPTION
1	601 50 51 96	HANDLE, UPPER
2	601 50 51 97	BAIL, CONTROL
3	601 50 51 29	NUT, 5/16-18 HEX
4	601 40 00 69	KNOB, WING
5	601 00 24 13	WASHER, FORM .344 I.D.
6	601 00 21 50	BOLT, 5/16-18 X 2.00
7	601 50 51 99	HANDLE, LOWER
8	601 50 51 69	SCREW, 1/4-20 X 1.25
9	601 40 00 80	WASHER, FLAT .281 X .63 X .065
10	601 40 00 86	NUT, .25-20 HEX CONTROL LOCK
11	601 00 13 95	BOOT, CLUTCH SPRING
12	601 00 13 92	CABLE, UPPER CONTROL
13	601 00 13 93	BRACKET, CABLE ADJUST
14	601 00 13 94	CABLE, LOWER CONTROL
15	601 00 13 96	SPRING, EXTENSION .75 O.D. X .069 X 2.00

Footnotes

The above parts group applies to the following Mfg. Nos.:

6210530x37NA 5021R 6210540x37NA 5021E

Briggs and Stratton Yard Power Products Group
Copyright © 2007 by Briggs and Stratton Corporation	13	TP 400-4686-02-ST-Q
Milwaukee, WI, USA. All rights reserved	13	TP 400-4686-02-ST-Q

Page 36

Image 36

Husqvarna 5021 R Handle Assembly, Ref No, Description, Footnotes, The above parts group applies to the following Mfg. Nos

Contents

Safety, Assembly, Operation, and Maintenance Operator’s ManualModels 5021 R 531309638 6210530X37NA 5021 E 531309639 6210540X37NAINTRODUCTION RESPONSIBILITY OF THE OWNERFOR YOUR RECORDS RULES FOR SAFE OPERATION Hazard Symbols and the meaningsOperating Symbols and their meanings the equipmentRULES FOR SAFE OPERATION Safe Operation Practices for SnowthrowersAs Recommended By American National Standards Institute ANSI TrainingService, Maintenance And Storage RULES FOR SAFE OPERATIONChildren Clearing A Clogged Discharge ChuteTABLE OF CONTENTS TROUBLESHOOTING CHARTSAFETY DECALS Decals SAFETY DECALSREF NO DESCRIPTIONWARRANTY STATEMENT OWNER’S INFORMATIONSECTION 1 LIMITED WARRANTY SECTION 2 HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTYWARRANTY STATEMENT SECTION 3 ITEMS NOT COVERED BY THIS WARRANTYSECTION 6 PROCEDURE TO OBTAIN WARRANTY CONSIDERATION OWNER’S INFORMATIONASSEMBLY WARNING Before doing any assembly or maintenance to the snowthrowerremove the wire from the spark plug PARTS BAG CONTENTSASSEMBLY ADD OIL TO THE ENGINEADD FUEL TO THE ENGINE explosion can cause severe burns or deathASSEMBLY BEFORE YOU OPERATEFRPSOHWHG FDUWRQOPERATION Control and Equipment Features FigureEngine Features Figure HOW TO CONTROL DISCHARGE OF SNOW or the auger housing and before leaving the snow throwerHOW TO THROW SNOW HOW TO STOP DISCHARGING SNOWHOW TO STOP THE ENGINE HOW TO START THE ENGINEHOW TO START A COLD ENGINE OPERATIONHOW TO START A WARM ENGINE HOW TO START A WARM ENGINE WITH A FROZEN STARTERHow To Use A Clean-Out Tool OPERATIONOPERATION Dry and Average SnowWet Packed Snow Snow Banks And DriftsMAINTENANCE repair, disconnect the wire from the spark plugENGINE POWER RATING INFORMATION CUSTOMER RESPONSIBILITIESMAINTENANCE HOW TO REMOVE THE TOP COVERAFTER EACH USE LUBRICATION BEFORE STORAGEMAINTENANCE HOW TO ADJUST THE AUGER CONTROL CABLEHOW TO REMOVE THE BELT COVER MAINTENANCE HOW TO REPLACE THE DRIVE BELTMAINTENANCE HOW TO REPLACE THE AUGERHOW TO ADJUST THE BRAKE PAD MAINTENANCE HOW TO REPLACE THE SPARK PLUGHOW TO PREPARE THE SNOWTHROWER FOR STORAGE repair, disconnect the wire from the spark plugMAINTENANCE HOW TO ORDER REPLACEMENT PARTSTROUBLESHOOTING CHART powerDifficulty starting Engine runs erraticEngine And Frame Assembly use the standard hardware torque specification chartBriggs and Stratton Yard Power Products Group 0003Engine And Frame Assembly REF NODESCRIPTION FootnotesEngine And Frame Assembly use the standard hardware torque specification chartBriggs and Stratton Yard Power Products Group 0003Engine And Frame Assembly REF NODESCRIPTION FootnotesAuger And Control Assembly use the standard hardware torque specification chartBriggs and Stratton Yard Power Products Group 0005Auger And Control Assembly REF NODESCRIPTION FootnotesDischarge Chute use the standard hardware torque specification chartBriggs and Stratton Yard Power Products Group 0007Discharge Chute REF NODESCRIPTION FootnotesHandle Assembly use the standard hardware torque specification chartBriggs and Stratton Yard Power Products Group 0011Handle Assembly REF NODESCRIPTION FootnotesChute Rod Assembly use the standard hardware torque specification chartBriggs and Stratton Yard Power Products Group 0009Chute Rod Assembly REF NODESCRIPTION FootnotesDecals use the standard hardware torque specification chartBriggs and Stratton Yard Power Products Group 0015Decals REF NODESCRIPTION FootnotesWheels use the standard hardware torque specification chartBriggs and Stratton Yard Power Products Group 0013Wheels REF NODESCRIPTION Footnotes