TO REMOVE WHEELS (See Fig. 22)

Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN

OUTER HOLE

 

INNER

 

HOLE

WHEEL

WHEEL HUB

FIG. 22

NOTE: To seal punctures or prevent fl at tires due to slow leaks, tire sealant may be purchased from your local parts dealer.Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualifi ed service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS”in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

 

IMPORTANT: It is important to prevent gum deposits from

 

forming in essential fuel system parts such as carburetor,

 

fuel hose, or tank during storage.Also, alcohol blended fuels

 

(called gasohol or using ethanol or methanol) can attract

 

moisture which leads to separation and formation of acids

 

during storage. Acidic gas can damage the fuel system of

 

an engine while in storage.

18

 

Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

Do not store gasoline from one season to another.

Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

Cover your snow thrower with a suitable protective cover that does not retain moisture.Do not use plastic.Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ exhaust area is still warm.

Page 18
Image 18
Husqvarna 8524STE owner manual Storage, Other

8524STE specifications

The Husqvarna 8524STE is a top-tier snowblower designed for both efficiency and user-friendly operation. This powerful machine is engineered to tackle heavy snowfall, making it an essential tool for homeowners in winter climates.

One of the standout features of the Husqvarna 8524STE is its robust 24-inch clearing width. This wide design allows users to clear large areas quickly and effectively. Equipped with a powerful 208cc engine, the snowblower delivers exceptional performance, ensuring reliable starting in cold temperatures and a high throwing distance for snow.

The Husqvarna 8524STE employs a dual-stage snow removal system, which combines both an auger and an impeller. This two-step process allows for the efficient intake and powering of snow into the chute for dispersal at a significant distance. The heavy-duty steel auger can cut through compacted snow and ice, reducing the effort required by the user.

Another notable technology featured in the Husqvarna 8524STE is its electric start system. This allows for easy and quick starting with the push of a button, eliminating the hassle of manual pull starts, especially in frigid temperatures. Additionally, the snowblower features a friction disc transmission that offers six forward speeds and two reverse speeds, enabling users to adjust their pace according to their specific snow-clearing needs.

Comfort is also a priority with this model. The ergonomic handle is designed for better grip, and the controls are well-placed for ease of use. The handle height can be adjusted to accommodate different user heights, ensuring that everyone can operate the machine comfortably.

The Husqvarna 8524STE further enhances its usability with a chute rotation that can be easily adjusted from the operator’s position. This feature provides precise control over the direction in which the snow is thrown, allowing users to clear their driveways, sidewalks, and walkways efficiently.

For added safety, the snowblower includes features such as a transparent fuel tank for easy monitoring of fuel levels and LED headlights for increased visibility during nighttime operations.

In summary, the Husqvarna 8524STE combines powerful performance with user-friendly features. Its durable construction, advanced technologies, and thoughtful design make it one of the best choices on the market for those looking to tackle winter's challenges. Whether you face heavy snowfalls or light flurries, this snowblower is built to handle it all with ease and efficiency.