SERVICE AND

TO REMOVE BELT GUARD (See Fig. 19)

•Remove two (2) cap nuts and washers from side of belt guard.

•Loosen (do not remove) tine shield nut on underside of tine shield.

ePull belt guard out and away from unit.

eReplace belt guard by reversing above procedure. Be sure slot in bottom of belt guard is under head of tine shield bolt and all nuts are tightened securely.

_"[-[_f/JA CAP NUTS

ANDWASHERS

_ / TINE SHIELD NUT

Fig. 19

ADJUSTMENTS

•Recheck in "ON" position and adjust if necessary.

NOTE: If"ON" position check required adjustment, recheck "OFF" position adjustment to insure tines do not rotate when control is "OFF" (up).

TINE CONTROL "OFF" POSITION

BODY

TINE CONTROL "ON" POSITION

CABLE

TINE CONTROL CABLE

TINE OPERATION CHECK (See Fig. 20)

WARNING: Disconnect spark plug wire from spark plug to prevent starting while checking tine operation.

For proper tine operation, forward tine control lever must be against control body and all slack removed from inner wire of control cable when control is in the "OFF" (up) position.

Iflever and cable are loose, loosen cable clip at lower end of cable. Pull up on cable to remove slack, without extending spring on end of cable, and retighten cable clip.

FINAL CHECK "OFF" POSITION

•With tine control "OFF" (up), push down on handle to raise tines off the ground.

Slowly pull recoil starter handle while observing tines. Tines should not rotate.

If tines rotate, inner wire of control cable is too tight which is extending lower spring and engaging tines. Loosen cable clip and push down on cable only enough to relieve spring tension. Tighten cable clip.

Recheck in "OFF" position and adjust if necessary.

FINAL CHECK "ON" POSITION

•With tine control "ON" (held down to handle) push down on handle to raise tines off the ground.

•Slowly pull recoil starter handle while observing tines. Tines should rotate forward.

•If tines do not rotate, inner wire of control cable is too loose. Loosen cable clip and pull cable up to remove slack and retighten clip.

Fig. 20

TO REPLACE V=BELTS (See Figs. 21 and 22)

Replace V-belts if they have stretched considerably or if they show cracks or frayed edges. There are two (2) V-belts -forward (inside) and reverse (outside).

Belt guard must be removed to service belts. See "TO REMOVE BELT GUARD" in this section of manual.

NOTE: Observe carefully routing of both belts and location of all belt guides before removing belts.

BELT REMOVAL

•Remove reverse idler pulley from idler arm.

•Remove reverse (outside) V-belt.

•Remove forward (inside) V-belt from transmission pulley first and then from engine pulley.

BELT REPLACEMENT

•Install new forward (inside) V-belt to engine pulley first then to transmission pulley. Be sure belt is positioned on inside groove of both pulleys, inside all belt guides and rests on idler pulley.

•Before installing reverse (outside) V-belt, turn belt"inside out". Twist so wide, flat surface of belt is to inside.

•Wrap V-belt around reverse idler pulley and reassemble idler to idler arm. Tighten securely. Be sure belt is between reverse idler pulley and idler arm pin.

•Install belt to outside groove of transmission pulley. Be sure belt is inside all belt guides and rests on outside groove of engine pulley.

14

Page 13 Page 15
Page 14
Image 14
Husqvarna 917.29939 owner manual Service, Adjustments, To Remove Belt Guard See Fig, Tine Operation Check See Fig
Page 13 Page 15

917.29939 specifications

The Husqvarna 917.29939 is a remarkable lawn tractor that combines power, durability, and comfort for an exceptional mowing experience. Designed for residential use, this model is particularly suitable for homeowners with larger yards, ensuring efficient trimming and maintenance of expansive green spaces.

A key feature of the Husqvarna 917.29939 is its powerful 24 HP Kawasaki engine, which delivers robust performance for impressive mowing capabilities. The engine's reliability and efficiency mean users can tackle a variety of terrains and conditions without compromising on power. The hydrostatic transmission offers smooth and adjustable speed control, allowing users to maneuver with ease, making it ideal for navigating around obstacles like trees and flower beds.

The mower deck on the 917.29939 is a standout characteristic, featuring a 54-inch cutting width designed for optimal grass cutting efficiency. This wide deck enables quicker mowing sessions, enabling users to cover more ground in less time. Additionally, it features an adjustable cutting height system, allowing the user to easily customize the grass length according to their preference or seasonal needs.

Comfort is also a priority in the design of the Husqvarna 917.29939. The ergonomically designed seat offers maximum comfort during extended mowing sessions, while the easy-to-reach control panel makes operating the tractor a breeze. The wide, soft-touch steering wheel ensures a comfortable grip, and the rubberized foot pedals provide a stable footing for the operator.

Another notable technology featured in this tractor is the integrated mulching capability, which allows for nutrient recycling by finely chopping and redistributing grass clippings back onto the lawn. This not only improves lawn health but also reduces the need for bagging, saving time and effort.

For added convenience, the Husqvarna 917.29939 comes equipped with a durable, reinforced frame and sturdy wheels designed to withstand rough terrains. The tractor also includes easy service points, making regular maintenance less of a chore.

In summary, the Husqvarna 917.29939 lawn tractor is a durable, powerful, and user-friendly machine that stands out in the realm of residential lawn care. With its combination of advanced features, ergonomic design, and efficient cutting performance, it represents an excellent investment for anyone serious about maintaining a pristine lawn.
Top Page Image Contents