OPERATION

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the 1/2" hex nuts, then moving skid plate to desired position. Be sure both plates are adjusted evenly. Tighten securely.

SCRAPER BAR (See Fig. 19)

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

HIGH POSITION

HEX

(LOW GROUND

CLEARANCE)

NUTS

 

AUGER

 

HOUSING

FREEWHEEL POSITION

TRANSMISSION ENGAGED

FIG. 21

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 22)

The engine on your snow thrower has been shipped, from the factory, already filled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

LOW POSITION

SCRAPER

(HIGH GROUND

BAR

CLEARANCE)

SKID PLATE

 

FIG. 19

TO USE DRIFT CUTTERS (See Fig. 20)

Use the drift cutters to cut through deep snowdrifts that are higher than the front of the snow thrower.

Loosen adjustment nuts enough to allow drift cutter to be raised to highest position and tighten nuts securely. Repeat for opposite side of snow thrower.

When not using drift cutters, loosen adjustment nuts, lower to storage position and tighten nuts securely.

AUGER

HOUSING

CHOKE CONTROL

SAFETY

IGNITION

KEY

RECOIL

STARTER

HANDLE

THROTTLE PRIMER ENGINE OIL FILL CAP / DIPSTICK

GASOLINE

FILLER CAP

FUEL SHUT-

OFF VALVE

STARTER BUTTON

POWER CORD PLUG

STORAGE

DRIFT

POSITION

CUTTER

ADJUST-

MENT NUTS

FIG. 20

TO TRANSPORT (See Fig. 21)

When pushing or towing your snowthrower, be sure to disengage transmission by placing freewheel control into FREEWHEEL position. Freewheel control is located at the rear of snowthrower.

Pull freewheel control out to FREEWHEEL position.

To reengage transmission, push control back in.

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 22

ADD GASOLINE (See Fig. 22)

Fill fuel tank to bottom of tank filler neck. Do not over- fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

12

Page 12
Image 12
Husqvarna 924SB-XLS owner manual Before Starting the Engine

924SB-XLS specifications

The Husqvarna 924SB-XLS is a robust and highly efficient snow blower designed for homeowners and professionals who need to tackle heavy snowfall with ease. Built with power, durability, and user-friendly features, this machine ensures effective snow removal across various surfaces.

One of the standout features of the Husqvarna 924SB-XLS is its powerful engine, equipped with a reliable 243cc 2-cycle motor. This engine delivers a significant amount of torque, enabling the snow blower to handle even the most stubborn, packed snow. The engine is designed for easy starting, and its high-performance design ensures that the blower can operate efficiently in extremely cold conditions.

The snow blower features a durable and robust auger system, which is capable of clearing a path 24 inches wide and up to 23 inches deep. The heavy-duty auger, combined with its powerful intake, helps efficiently break up and transport the snow through the discharge chute. Additionally, the stainless steel construction of the auger enhances its longevity, making it resistant to wear and tear over time.

An important aspect of the Husqvarna 924SB-XLS is its four-way adjustable discharge chute, which allows users to direct the expelled snow precisely where they want it. This feature is particularly useful for managing snow piles and optimizing clearing efficiency. The chute can be easily adjusted from the operator’s position, ensuring minimal interruption during operation.

The snow blower is equipped with features designed for user comfort and ease of operation. The handlebar is ergonomically designed and height-adjustable, allowing operators of different sizes to work comfortably. Furthermore, the oversized tires provide excellent traction on slippery surfaces, making it easier to maneuver through deep snow.

The Husqvarna 924SB-XLS also includes a built-in electric starter, allowing for hassle-free starting on colder days. With its powerful performance, user-friendly features, and durable construction, the Husqvarna 924SB-XLS is an excellent choice for anyone in need of a high-performance snow blower. Its combination of technology and engineering makes it a reliable tool for efficiently managing winter weather challenges. Whether for residential use or small commercial jobs, this snow blower offers reliability you can count on.