OPERATION
CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.
NOTE:Adjust gauge wheels with tractor on a flat level | REVERSE OPERATION SYSTEM (ROS) | ||||
Your tractor is equipped with a Reverse Operation System | |||||
surface. |
|
| |||
• Adjust mower to desired cutting height (See “TO AD- | (ROS). Any attempt by the operator to travel in the reverse | ||||
direction with the attachment clutch engaged will shut off | |||||
JUST MOWER CUTTING HEIGHT” in the Operation | |||||
the engine unless ignition key is placed in the ROS "ON" | |||||
section of this manual). |
| ||||
| position. |
| |||
With mower in desired height of cut position, gauge |
| ||||
|
| ||||
wheels should be assembled so they are slightly off | WARNING: Backing up with the attachment clutch en- | ||||
the ground. Install gauge wheel in appropriate hole | gaged while mowing is strongly discouraged. Turning the | ||||
with shoulder bolt, 3/8 washer, and | ROS "ON", to allow reverse operation with the attachment | ||||
tighten securely. |
| clutch engaged, should only be done when the operator | |||
Repeat for opposite side installing gauge wheel in same | decides it is necessary to reposition the machine with the | ||||
adjustment hole. |
| attachment engaged. Do not mow in reverse unless | |||
|
|
| absolutely necessary. |
| |
| LOCKNUT | USING THE REVERSE OPERATION SYSTEM | |||
|
|
| |||
|
| 3/8 WASHER | (See Fig. 13) |
| |
|
|
| Only use if you are certain no children or other bystanders | ||
|
|
| will enter the mowing area. |
| |
|
|
| • Move motion control lever to neutral (N) position. | ||
|
|
| • With engine running, turn ignition key counterclockwise | ||
|
|
| to ROS "ON" position. |
| |
|
|
| • Look down and behind before and while backing. | ||
|
|
| • Slowly move motion control lever to reverse (R) position | ||
|
| SHOULDER BOLT | to start movement. |
| |
|
|
| • When use of the ROS is no longer needed, turn the | ||
| FIG. 11 |
| ignition key clockwise to engine "ON" position. | ||
|
|
|
| ||
TO OPERATE MOWER (See Fig. 12) | ROS "ON" Position | Engine "ON" Position | |||
| (Normal Operating) | ||||
Your tractor is equipped with an operator presence sensing |
| ||||
|
| ||||
switch. Any attempt by the operator to leave the seat with the |
|
| |||
engine running and the attachment clutch engaged will shut off |
|
| |||
the engine.You must remain fully and centrally positioned in the |
|
| |||
seat to prevent the engine from hesitating or cutting off when |
|
| |||
operating your equipment on rough, rolling terrain or hills. |
|
| |||
Select desired height of cut. |
|
| 8 | ||
|
|
|
| ||
Lower mower with attachment lift control. |
| 0282 | |||
|
| ||||
Start mower blades by engaging attachment clutch | FIG. 13 | ||||
control. |
|
| |||
|
|
|
| ||
TO STOP MOWER BLADES - disengage attachment |
|
| |||
clutch control. |
|
|
| ||
|
| ATTACHMENT |
|
| |
|
| LIFT LEVER |
|
| |
|
| HIGH POSITION |
|
| |
|
| LOW |
|
| |
ATTACHMENT | POSITION |
|
| ||
|
|
| |||
CLUTCH SWITCH |
|
|
| ||
"DISENGAGED" |
|
|
| ||
POSITION | "ENGAGED" |
|
|
| |
|
|
|
| ||
| POSITION |
|
|
| |
| 02710 |
|
|
| |
| FIG. 12 |
|
|
|
14