Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna GTH220 TO ADJUST MOTION CONTROL LEVER See Fig, Transmission Removal/Replacement

Models: GTH220

1 56

Download 56 pages 33.52 Kb

Page 24

TO ADJUST MOTION CONTROL LEVER (See Fig. 29)

SERVICE AND ADJUSTMENTS

TO ADJUST MOTION CONTROL LEVER (See Fig. 29)

The motion control lever has been preset at the factory and adjustment should not be necessary.

If for any reason the motion control lever will not hold its position while at a selected speed, it may be adjusted at the friction pack located on the right side of chassis.

•Park tractor on level surface. Stop tractor by turning ignition key to “OFF” position and engage parking brake.

•Place motion control lever in neutral (N) position.

•While holding locknut, loosen jam nut

•Tighten locknut 1/4 turn.

•While holding locknut, tighten jam nut securely.

NOTE: If for any reason the effort to move the motion control lever becomes too excessive, reverse the above adjustment procedure by loosening locknut 1/4 turn.

Road test tractor after adjustment and repeat procedure if necessary.

LOCKNUT

JAM

NUT

FIG. 29

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation before operating the tractor. See “PURGE TRANSMISSION” in Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN ADJUSTMENT

Front wheel toe-in is required for proper steering operation. Toe-in was set at the factory and adjustment should not be necessary. If parts in the front axle or steering mechanism have been replaced or damaged, check toe-in and adjust if necessary.

TO CHECK TOE-IN (See Fig. 30) -

•Position front wheels straight ahead.

•Measure distance between wheels at front and rear of tires (dimensions “A” and “B”).

•Front dimension “A” should be 1/8" to 1/4" less than rear dimension “B”.

TO ADJUST TOE-IN (See Figs. 30 and 31) -

•Loosen jam nuts at adjustment sleeves on tie rod.

•Adjust tie rod until dimension “A” is 1/8" to 1/4" less than dimension “B”.

•Tighten jam nuts securely.

24

Image 24

Husqvarna GTH220 TO ADJUST MOTION CONTROL LEVER See Fig, Transmission Removal/Replacement, Front Wheel Toe-In Adjustment

Contents

GTH220 SAFETY RULES IV. SERVICESafe Operation Practices for Ride-On Mowers I. GENERAL OPERATIONPRODUCT SPECIFICATIONS CUSTOMER RESPONSIBILITIESTABLE OF CONTENTS INDEXCONTENTS OF HARDWARE PACK Parts Bag contents shown full sizeParts bag contents not shown full size Parts packed separately in cartonASSEMBLY TOOLS REQUIRED FOR ASSEMBLYCONNECT BATTERY See Fig TO REMOVE TRACTOR FROM CARTONINSTALL SEAT See Fig TO ATTACH NOSE ROLLER See FigCHECK TIRE PRESSURE CHECK BRAKE SYSTEMINSTALL MOWER AND DRIVE BELT See Figs. 5 and align deck pins with the holes in suspension armsCHECK DECK LEVELNESS CHECK FOR PROPER POSITION OF ALL BELTSTO ATTACH FRONT BUMPER See Fig ASSEMBLYCHECKLIST OPERATION HEIGHT ADJUSTMENT KNOB - Used to adjust the mower height KNOW YOUR TRACTOROPERATION HOW TO USE YOUR TRACTOR TO ADJUST MOWER CUTTING HEIGHT See FigTO SET PARKING BRAKE See Fig STOPPING See FigTO ADJUST GAUGE WHEELS See Fig TO OPERATE MOWER See Figs. 7 andTO OPERATE ON HILLS TO TRANSPORT See Figs. 7 andINDICATOR LIGHTS BEFORE STARTING THE ENGINECHECK ENGINE OIL LEVEL See Fig ADD GASOLINEMOWING TIPS PURGE TRANSMISSIONning OPERATIONLUBRICATION CHART MAINTENANCE SCHEDULECUSTOMER RESPONSIBILITIES GENERAL RECOMMENDATIONSBATTERY TRACTORBRAKE OPERATION TIRESCLEAN AIR SCREEN See Fig ENGINETRANSAXLE COOLING TRANSAXLE PUMP FLUIDCLEANING CLEAN AIR INTAKE/COOLING AREASAIR FILTER See Fig ENGINE OIL FILTERSERVICE AND ADJUSTMENTS TO INSTALL MOWERTO LEVEL MOWER HOUSING CAUTION BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTSTO REPLACE MOWER DRIVE BELT SERVICE AND ADJUSTMENTSTO ADJUST ATTACHMENT CLUTCH See Fig TO REPLACE MOWER BLADE DRIVE BELT See FigSERVICE AND ADJUSTMENTS TO ADJUST BRAKE See Fig TO REPLACE MOTION DRIVE BELT See FigSERVICE AND ADJUSTMENTS TRACTOR V-BELT DRIVE SCHEMATICTO ADJUST MOTION CONTROL LEVER See Fig TRANSMISSION REMOVAL/REPLACEMENTTO ADJUST STEERING WHEEL ALIGNMENT FRONT WHEEL TOE-IN ADJUSTMENTTO START ENGINE WITH A WEAK BATTERY See Fig FRONT WHEEL CAMBERTO REMOVE WHEEL FOR REPAIRS See Fig SERVICE AND ADJUSTMENTSTO ADJUST ATTACHMENT LIFT SPRING See Fig TO REMOVE HOOD AND GRILL ASSEMBLY See FigTO REPLACE HEADLIGHT BULB INTERLOCKS AND RELAYSTO ADJUST THROTTLE CONTROL CABLE See Fig TO ADJUST CHOKE CONTROL See Figs. 36 andSERVICE AND ADJUSTMENTS ENGINETO ADJUST CARBURETOR See Fig SERVICE AND ADJUSTMENTSSTORAGE OTHERFUEL SYSTEM ENGINE OILTROUBLESHOOTING POINTS PROBLEMCAUSE CORRECTIONTROUBLESHOOTING POINTS PROBLEMCAUSE CORRECTIONSERVICE NOTES SCHEMATIC TRACTOR - MODEL NO. GTH220 954830167AINDICATOR LIGHTS IGNITION SWITCHREPAIR PARTS ELECTRICALTRACTOR - MODEL NO. GTH220 954830167A FOOTKEY PART NO. NO. DESCRIPTION REPAIR PARTSTRACTOR - MODEL NO. GTH220 954830167A ELECTRICAL47120 REPAIR PARTSCHASSIS AND ENCLOSURES TRACTOR - MODEL NO. GTH220 954830167ACHASSIS AND ENCLOSURES PARTDESCRIPTION REPAIR PARTSGROUND DRIVE REPAIR PARTSTRACTOR - MODEL NO. GTH220 954830167A REPAIR PARTS TRACTOR - MODEL NO. GTH220 954830167AGROUND DRIVE PARTSTEERING ASSEMBLY REPAIR PARTSTRACTOR - MODEL NO. GTH220 954830167A 37,39REPAIR PARTS STEERING ASSEMBLYTRACTOR - MODEL NO. GTH220 954830167A PARTENGINE REPAIR PARTSTRACTOR - MODEL NO. GTH220 954830167A SPARK ARRESTER KITREPAIR PARTS TRACTOR - MODEL NO. GTH220 954830167AENGINE KEY PART NO. NO. DESCRIPTIONSEAT ASSEMBLY REPAIR PARTSTRACTOR - MODEL NO. GTH220 954830167A PARTDECALS WHEELS & TIRESREPAIR PARTS TRACTOR - MODEL NO. GTH220 954830167ALIFT ASSEMBLY 1225REPAIR PARTS TRACTOR - MODEL NO. GTH220 954830167AREPAIR PARTS LIFT ASSEMBLYTRACTOR - MODEL NO. GTH220 954830167A KEY PART NO. NO. DESCRIPTIONMOWER DECK REPAIR PARTSTRACTOR - MODEL NO. GTH220 954830167A REPAIR PARTS TRACTOR - MODEL NO. GTH220 954830167AMOWER DECK PARTTRANSAXLE HYDRO GEAR MODEL NUMBER REPAIR PARTSTRACTOR - MODEL NO. GTH220 954830167A REPAIR PARTS TRACTOR - MODEL NO. GTH220 954830167ATRANSAXLE HYDRO GEAR MODEL NUMBER DESCRIPTIONTRANSAXLE PUMP- - MODEL NUMBER BDU-10L-118 REPAIR PARTSTRACTOR - MODEL NO. GTH220 954830167A PARTSERVICE NOTES SIGHTING GUIDE THISDOTTED IS AWARRANTY STATEMENT SECTION 1 LIMITED WARRANTYSECTION 2 HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY SECTION 3 ITEMS NOT COVERED BY THIS WARRANTY532150629 08.17.95 KFSW