Manuals / IBM / Computer Equipment / Network Card

IBM 100/10 Driver installation, VIA Sound Blaster Installation, Before you begin, drivers

Models: 100/10 PCM-9575

1 162

Download 162 pages 19.87 Kb

Page 87

6.2.2 VIA Sound Blaster Installation

Follow these steps to enable the Sound Blaster Pro compatible functions.

Step 1. Enable the Sound Blaster first on the BIOS setting of the "Onboard Legacy Audio" and "On-Chip Sound".

Step 2. Run the "Install.exe". A:> INSTALL

Step 3. The program will copy the relative files into the directory which you assign. Next, the program will insert the following new line into the AUTOEXEC.BAT and copy the original AUTOEXEC.BAT to AUTOEXEC.VIA.

C: \VIAUDIO\VIAUDIO.COM

Step 4. Reboot the system when the installation is complete.

Step 5. Uninstall by deleting the new line from the AUTOEXEC.BAT.

6.3 Driver installation

6.3.1 Before you begin

Please read the instructions in this chapter carefully before you attempt installation. The audio drivers for the PCM-9575 board are located on the audio driver CD. Run the supplied SETUP program to install the drivers; don’t copy the files manually.

Note:	The files on the software installation diskette
	are compressed. Do not attempt to install the
	drivers by copying the files manually. You must
	use the supplied SETUP program to install the
	drivers.

77	Chapter 6 Audio Setup

Image 87

IBM 100/10, PCM-9575 user manual Driver installation, VIA Sound Blaster Installation, Before you begin, drivers

Contents

PCM-9575 Acknowledgements CopyrightPacking List Model No. ListDescription PCM-9575 User’s Manual Installation Contents2.14.2Main power connector, +5 V, +12 V CN5 4.1.1 Table of Contents6.2.1 Figure F.3 PCM-9575 Mech Drawing solder side System AssignmentsFigure F.1 PCM-9575 Mechanical Drawing Figure F.2 PCM-9575 Mech Drawing component sidePage General Information CHAPTERChapter 1 General Information Chapter 1 Introduction 1.1 IntroductionHighly integrated multimedia SBC 1.2 Features 1.3 Specifications1.3.1 Standard EBX SBC Functions Solid State Disk 1.3.2 VGA/LCD Interface1.3.4 Audio function 1.3.5 TV-out optionalTypical Power requirements Max1.3.6 PCI bus Ethernet interface 1.3.7 Mechanical and Environmental1.4 Board layout dimensions Figure 1.1 Board layout dimensionsPCM-9575 User’s Manual Installation Chapter 2 InstallationCHAPTER Table 2.2 Connectors Chapter 2 Installation2.2 Connectors 2.1 JumpersTable 2.2 Connectors CRT display connectorChapter 2 Installation 2.3 Locating jumpers Figure 2.1 Jumper locationsPCM-9575 User’s Manual 2.4 Locating Connectors Figure 2.2 Connectors component sideChapter 2 Installation 2.5 Setting Jumpers Table 2.3 CMOS clear JP4 2.6 Clear CMOS JP42.7 Installing DIMMs 2.8 IDE, CDROM hard drive connector CN14, CN162.8.1 Connecting the hard drive 2.9.1 CompactFlash CN26 2.10 Floppy drive connector CN182.9 Solid State Disk 2.10.1 Connecting the floppy drive2.11 Parallel port connector CN15 2.12 Keyboard and PS/2 mouse connector CN252.13 Power & HDD LED, Reset Button Connector CN13, CN22 2.13.2 Reset switch CN22 2.14 Power connectors CN27, CN5, FAN12.15 ATX power control connector CN3, CN23 2.13.1 Power & HDD LED CN13to main power 2.16 IR connector CN242.17 Audio interfaces CN4, CN2 to CN3 ATX features connector ATX power supply2.18.1 COM2 RS-232/422/485 setting JP6 2.18 COM port connector CN192.17.1 Audio connector CN4 2.17.2 CD audio input connector CN22.19.3 Extension flat panel connector CN10 2.19 VGA/LCD/LVDS interface connections2.19.1 CRT display connector CN8 2.19.2 Flat panel display connector CN11Table 2.4 S1 Panel Type select 2.20 TV-out interface optional CN12.21.2 Network boot 2.21 Ethernet configuration2.22 Watchdog timer configuration 2.21.1 100Base-T connector CN122.23 USB connectors CN20, CN28 2.22.1 Watchdog timer action JP5Table 2.6 Watchdog timer action JP5 PCM-9575 User’s Manual CHAPTER Software ConfigurationEthernet interface configuration 25 Chapter 3 Software Configuration3.1 Introduction Chapter 3 Software ConfigurationTable 3.1 Connections to Toshiba LTM10C209A 3.2 Connections to Three Standard LCDs27 Chapter 3 Software Configuration 3.2.1 Connections to Toshiba LTM10C209A 640 x 480 TFT color LCDTable 3.2 Connections to Toshiba LTM15C151A 3.2.2 Connections to Toshiba LTM15C151A 1024 x 768 TFT color LCDLTM15C151A Table 3.1 Connections to Toshiba LTM10C209ATable 3.3 Connections to Toshiba LTM12C275A 29 Chapter 3 Software Configuration3.2.3 Connections to Toshiba LTM12C275A 800 x 600 TFT color LCD Table 3.2 Connections to Toshiba LTM15C151ATable 3.3 Connections to Toshiba LTM12C275A 3.3 Ethernet software configuration31 Chapter 3 Software Configuration For Ethernet installation, please see ChapterPCM-9575 User’s Manual CHAPTER Award BIOS SetupThis chapter describes how to set BIOS configuration data Chapter 4 Award BIOS Setuppress F1 to RESUME Chapter 4 Award BIOS Setup4.1 System test and initialization 4.1.1 System configuration verification4.2 Award BIOS setup 4.2.1 Entering setupFigure 4.1 BIOS setup program initial screen Figure 4.2 CMOS Features setup 4.2.2 Standard CMOS Features setup4.2.3 Advanced BIOS Features setup Figure 4.3 Advanced BIOS Features setupChapter 4 Award BIOS Setup 4.2.4 Advanced Chipset Features setup Figure 4.4 Advanced Chipset Features setupPCM-9575 User’s Manual Figure 4.5 Integrated Peripherals 4.2.6 Power Management SetupFigure 4.6 Power Management Setup 4.2.5 Integrated PeripheralsFigure 4.8 PC Health Status 4.2.7 PnP/PCI ConfigurationsFigure 4.7 PnP/PCI Configurations 4.2.8 PC Health StatusChapter 4 Award BIOS Setup 4.2.9 Frequency/Voltage ControlFigure 4.9 Frequency/Voltage Control Advanced BIOS Features menu, choose the 4.2.10 Load Optimized Defaults4.2.11 Set Password Figure 4.10 Load BIOS defaults screen4.2.12 Save & Exit Setup To Change PasswordTo Disable Password PCM-9575 User’s Manual 4.2.13 Exit Without SavingPCI SVGA Setup Chapter 5 PCI SVGA SetupCHAPTER 5.1.2 Display memory Chapter 5 PCI SVGA Setup5.1 Introduction 5.1.1 Chipset5.1.4 Dual/Simultaneous Display Figure 5.1 Selecting Display Settingsintended as examples only. Please follow the 5.2 Installation of the SVGA Driver5.2.1 Installation for Windows 1. The windows illustrations in this chapter areChapter 5 PCI SVGA Setup Step 2. Choose the Adapter tab, then press the Change... buttonStep 3. Press the Have Disk button PCM-9575 User’s Manual Step 4. Type in the pathD\Biscuit\9575\VGA\Win9xMe Step 5. Select the highlighted item, and click the OK buttonChapter 5 PCI SVGA Setup Step 7. Press “Yes” to rebootPCM-9575 User’s Manual 5.2.2 Installation for Windows 98/MeStep 2. Select “Adapter,” then “Change.” Chapter 5 PCI SVGA SetupStep 3. Press “Next,” then “Display a list....” Step 4. Press the “Have disk...” buttonPCM-9575 User’s Manual Then press “OK” Step 6. Select the highlighted item, then click “OK.” Chapter 5 PCI SVGA SetupStep 5. Insert the CD into the CD-ROM drive. Type in the path D\Biscuit\9575\VGA\Win9xMePCM-9575 User’s Manual Step 8. Press “Yes” to rebootChapter 5 PCI SVGA Setup Installation for Windows NTService Pack X X = 3, 4, 5, 6,... must be installed first, before you install the WindowsPCM-9575 User’s Manual Step 2. Choose the Settings tab, and press the Display Type buttonStep 3. Press the Change... button Chapter 5 PCI SVGA SetupPCM-9575 User’s Manual Step 4. Click the Have Disk... button Step 5. Type the pathD\Biscuit\VGA\WinNT Press the OK buttonStep 7. Press Yes to proceed Step 8. Press OK to reboot Chapter 5 PCI SVGA SetupStep 6. Select the highlighted item, and click the OK button PCM-9575 User’s Manual 5.2.4 Installation for WindowsStep 2. Choose the Video Controller VGA Compatible” button Chapter 5 PCI SVGA SetupPCM-9575 User’s Manual Step 3. Choose the Drive button, press “Update Driver...” buttonChapter 5 PCI SVGA Setup Step 4. Choose Display a list of... , then press “Next” buttonStep 5. Choose “Display adapters”, press “Next” button PCM-9575 User’s Manual Step 6. Click the “Have Disk” button5.2.5 Installation for Windows XP Step 8. Press “Finish to rebootChapter 5 PCI SVGA Setup PCM-9575 User’s Manual Step 2. Choose “Hardware” and “Device Manager”, press “OK” buttonStep 3. Choose “Video Controller VGA Compatible, press “OK” but- ton Chapter 5 PCI SVGA SetupStep 4. Choose Driver”, “Update Driver”, press “OK” button Step 5. Choose “Install from a list.....” , press “Next”PCM-9575 User’s Manual Chapter 5 PCI SVGA Setup Step 6. Choose “Don’t search. I will....”, press “Next” buttonStep 7. Choose “Display adapters”, press “Next” button PCM-9575 User’s Manual Step 8. Type the path D\Biscuit\9575\VGA\WinXP then press “OK” buttonVIA website 5.3 Further InformationStep 10. Press “Finish to reboot Chapter 5 PCI SVGA SetupPCM-9575 User’s Manual Audio Setup Chapter 6 Audio SetupCHAPTER 6.2.1 VIA Sound Blaster Pro compatible set up program Chapter 6 Audio Setup6.1 Introduction 6.2 DOS utilitiesare compressed. Do not attempt to install the 6.3 Driver installation6.2.2 VIA Sound Blaster Installation The files on the software installation diskette6.3.2 Windows 95/98 drivers Step 2. In the Add New Hardware Wizard window, click NextPCM-9575 User’s Manual Step 3. In the following Add New Hardware Wizard window, click Next for Windows to search for Plug and Play devices Step 5. In the following Add New Hardware Wizard window, select No, I want to select... and click Next Chapter 6 Audio Setup Step 8. In the Install From Disk window, click BrowsePCM-9575 User’s Manual Step 10. In the Install From Disk window, click OKStep 12. In the Add New Hardware Wizard window, click Next Chapter 6 Audio SetupPCM-9575 User’s Manual Step 13. The Copying Files... window will appear6.3.3 Windows NT drivers PCM-9575 User’s Manual Step 3. In the Add window, select the Unlisted... item and click OKChapter 6 Audio Setup Step 6. In the System Setting Change window, click Restart Now6.3.4 Windows 2000 Drivers Step 2. Choose “Multimedia Audio Controller” buttonPCM-9575 User’s Manual Step 3. Choose “Driver button, press “Update Driver” button Chapter 6 Audio SetupStep 4. Choose “Sound, video and game controllers”, press “Next” Step 5. Click the “Have Disk...” button Step 7. Click “Have Disk” buttonPCM-9575 User’s Manual Chapter 6 Audio Setup Step 8. Press “Next” button Step 9. Press “Finish” to rebootPCM-9575 User’s Manual PCI Bus Ethernet Interface CHAPTER93 Chapter 7 PCI Bus Ethernet Interface 7.2.1 Installation for MS-DOS and Windows 7.2 Installation of Ethernet driverChapter 7 PCI Bus Ethernet Interface 7.1 Introduction7.2.2 Installation for Windows Step 2. a. Click Add and prepare to install network functions95 Chapter 7 PCI Bus Ethernet Interface Step 4. a. Click Have Disk to install the driver Step 3. a. Select the Adapter item to add the Ethernet cardPCM-9575 User’s Manual 97 Chapter 7 PCI Bus Ethernet Interface b. Click OK7.2.3 Installation for Windows Step 1. Open Device ManagerPCM-9575 User’s Manual 99 Chapter 7 PCI Bus Ethernet Interface StepPCM-9575 User’s Manual Step Step101 Chapter 7 PCI Bus Ethernet Interface Step StepPCM-9575 User’s Manual Step Step103 Chapter 7 PCI Bus Ethernet Interface 7.2.4 Installation for Windows NTPCM-9575 User’s Manual b. Click Next Step 3. a. Click Select from list105 Chapter 7 PCI Bus Ethernet Interface Step 4. Click “Have Disk.”Step 5. a. Insert the Utility CD ROM b. Fill in the correct path D\Biscuit\9575\LAN\8139C\winnt4 c. Click OKPCM-9575 User’s Manual Step 6. Check the highlighted item, and click “OK.”7. Click “Next” to continue setup Step 8. Choose the networking protocols, then click Next107 Chapter 7 PCI Bus Ethernet Interface Step 9. Select the correct Network Services then click Next Step 10. Click “Next” to continue setupPCM-9575 User’s Manual Intel website 7.3 Further information11. Click “Next” to start the network Realtek websitePCM-9575 User’s Manual Programming the Watchdog Timer AppendixAppx.A A.1 Supported Input Timing Modes Appendix A Programming the Watchdog TimerAppx.A 80 END1070 RETURN 2090 RETURNTPC-642 User’s Manual Installing PC/104-Plus Modules AppendixAppx.B B.1 Installing PC/104-Plus Modules Appendix B Installing PC/104-Plus ModulesAppx.B Figure B.1 PC/104+ module mounting diagramTPC-642 User’s Manual Figure B.2 PC/104+ module dimensions mm ±0.1Appendix Pin AssignmentsTable C.1 IR connector FAN C.1 CPU Fan Power Connector FANC.2 Ethernet 10/100Base-T Connector CN12 Appendix C Pin AssignmentsTable C.4 Audio line-in connector CN2 C.3 Audio Connector CN4C.4 Audio In Connector CN2 Table C.3 Audio connector CN4PCA-6183 User’s Manual C.5 Main Power Connector CN5Table C.5 Main Power Connector CN5 Pin SignalAppx.C C.6 Keyboard and PS/2 Mouse Connector CN25Table C.6 Keyboard and mouse connector CN25 Pin SignalC.7 Floppy Disk Drive Connector CN18 Table C.7 Floppy Disk Drive Connector CN18PCA-6183 User’s Manual C.8 PC/104 plus Connectors CN17 Table C.8 PC/104+ connectors CN17Appx.C PCA-6183 User’s Manual Table C.8 PC/104+ connectors CN17C.9 IDE Hard Drive Connector CN14, CN16 Table C.9 IDE HDD connector CN14, CN16Appx.C C.10 Parallel Port Connector CN15 Table C.10 Parallel Port Connector CN15PCA-6183 User’s Manual Table C.12 Reset Button Connector CN22 C.11 Power & HDD LED ConnectorCN13C.12 Reset Button Connector CN22 Table C.11 Power & HDD LED Connector CN13Table C.14 LCD Inverter Backlight Connector CN6 C.13 USB Connector CN20, CN28C.14 LCD Inverter Backlight Connector CN6 Table C.13 USB Connector CN20, CN28Table C.16 CRT Display Connector CN8 C.15 IR Connector CN24C.16 CRT Display Connector CN8 Table C.15 IR Connector CN24PCA-6183 User’s Manual C.17 TV video Out Connector CN1Table C.17 TV video Out Connector CN1 Pin SignalAppx.C C.18 Flat Panel Connector CN11Table C.18 Flat Panel Connector CN11 The model number of the CN11 socket isPCA-6183 User’s Manual C.19 Extended Flat Panel Display Connector CN10Table C.19 Extended Flat Panel Display Connector CN10 The model number of the CN10 socket is16-bit C.20 LCD Signal MappingTable C.20 LCD Signal Mapping Appx.CTable C.22 Peripheral Power Connector CN27 C.21 LVDS Connector CN9C.22 Peripheral Power Connector CN27 Table C.21 LVDS Connector CN9C.23 COM Port Connector CN19 Table C.23 COM Port Connector CN19Appx.C C.24 CompactFlash Card Connector CN26 Table C.24 CompactFlash Card Connector CN26PCA-6183 User’s Manual Appx.C C.25 ATX Power Feature Connector CN3Table C.25 ATX Power Feature Connector CN3 Pin SignalPCA-6183 User’s Manual System Assignments AppendixAppx.D PCA-6183 User’s Manual Appendix D System AssignmentsD.1 System I/O Ports Table D.1 System I/O portsTable D.3 DMA channel assignments D.2 1st MB memory mapD.3 DMA channel assignments Table D.2 1st MB memory mapD.4 Interrupt assignments Table D.4 Interrupt assignmentsPCA-6183 User’s Manual Optional Extras for the PCM-9575 AppendixAppx.E PCM-9575 User’s Manual E.1 PCM-10586-5A00 cable kit for PCM-9575E.5 Optional PC/104+ to PCI Module E.4 ATX Power Control Cable CN3E.2 Optional LCD cables 10.4 TFT LCD panel CN14 E.3 Optional USB cable CN20PCM-9575 User’s Manual Mechanical Drawings AppendixAppx.F PCM-9575 User’s Manual F.1 Mechanical DrawingsAppx.F Figure F.2 PCM-9575 Mechanical Drawing component sidePCM-9575 User’s Manual Figure F.3 PCM-9575 Mechanical Drawing solder side