IBM S85 58

System Rack Attached to One I/O Drawer

System Rack Attached to TwoI/O Drawers

OR

SPCN

RIO1RIO0

Drawer 0, Primary

RIO1

RIO0

RIO2 RIO3

J14

J11

SPCN0, J15

SPCN1, J16

RIO1RIO0

SPCN

RIO1RIO0

Drawer 0

Drawer 1

RIO1

RIO0

RIO2 RIO3

J14

J11

SPCN0, J15

SPCN1, J16

58 S80, S85 Installation Guide

Contents

Main Page Contents iii iv Safety Notices danger v caution Electrical Safety Laser Safety Information vi Data Integrity and Verification vii Page About This Book ISO 9000 ix Online Publications Related Publications Trademarks x Chapter 1. System Installation Procedure Step 1. Inventory Electronic Service Agent for RS/6000 Users Guide PCI Adapter Placement Reference Diagnostic Information for Multiple Bus Systems Step 3. Check the Customer Environment 2 Step 4. Check Customer Outlets not Step 5. Set Up the System Racks 4 Page Page Step 6A. Attach the I/O Rack to a Concrete Floor Attaching the I/O Rack to a Concrete Floor must 8 Page Attaching the I/O Rack to a Concrete Floor Beneath a Raised Floor must 10 Page 12 Page Step 6B. Attach the System Rack to a Concrete Floor 14 Attaching the System Rack to a Concrete Floor Attaching the System Rack to a Concrete Floor Beneath a Raised Floor 16 Page Step 7. Attach the Front Electrical Outlet 18 Page Page Page Step 8. Attach the Rear Electrical Outlet Page Page Page Page Step 10. Install the I/O Rack Door Guide Page Step 14. Update the Device Records Step 15. Attach External Devices Step 16. Connect the Power Step 17. Power On and Check Out the System Diagnostic Information for Multiple Bus Systems Step 18. Service Processor Setup and Test Step 19. Install the Modem and Electronic Service Agent 30 Electronic Service Agent for RS/6000 Users Guide Step 20. Finish the Installation Page Page Chapter 2. Using the System Verification Procedure Step 1. Considerations before Running This Procedure Step 2. Loading the Diagnostics Step 3. Running System Verification Step 4. Additional System Verification 34 Step 5. Stopping the Diagnostics Page Page Page Page Appendix A. Communications Statements Federal Communications Commission (FCC) Statement European Union (EU) Statement Page Electromagnetic Interference (EMI) Statement - Taiwan Radio Protection for Germany Page Appendix B. Environmental Notices Product Recycling and Disposal Environmental Design Unit Emissions Page Appendix C. Notices Page Appendix D. Cabling the System Rack and I/O Rack Connecting JTAG and Operator Panel Cables Use the following figure to connect the JTAG and operator panel (OP) cables. 48 I/O Rack Rear Locations Page 10 EIA Unit I/O Drawer Rear View 52 10 EIA Unit I/O Drawer System board Locations 54 Service Processor Card Locations Fan Monitor Control (FMC) Card Locations (10 EIA Unit I/O Drawer) Power Distribution Board Locations 56 Connecting RIO and SPCN Cables System Rack Attached to One I/O Drawer 58 System Rack Attached to TwoI/O Drawers OR Drawer 0, Primary System Rack Attached to Three I/O Drawers System Rack Attached to Four I/O Drawers Appendix D. Cabling the System Rack and I/O Rack 59 60 System Rack Attached to TwoI/O Drawers System Rack Attached to Three I/O Drawers Drawer 1 or 2 Appendix D. Cabling the System Rack and I/O Rack 61 System Rack Attached to Four I/O Drawers 62 Appendix E. System Records S80 and S85 System Rack Cabling Configurations - SPCN Cabling 64 Primary I/O Drawer Device Records Table1. Internal and External Options in Primary Drawer (0) 66 Table2. Internal Files and Devices in Primary Drawer (0) 10 EIA Unit I/O Drawer (continued) Additional I/O Drawer Device Records 68 Table3. Internal and External Options in Secondary Drawer (1) Table4. Internal and External Options in Secondary Drawer (2) Table4. Internal and External Options in Secondary Drawer (2) (continued) Table5. Internal and External Options in Secondary Drawer (3) Table5. Internal and External Options in Secondary Drawer (3) (continued) 70 Page Page Readers Comments Wed Like to Hear From You BUSINESS REPLY MAIL