R E S I D E N T I A L
MEASURING FOR YOUR DOOR
1.Measure existing door width and height in feet and inches. This determines the size of door needed. The rough opening should be the same size as the door.
Width: ____________________ Height: ____________________
2.Measure for sideroom: 3 3/4 " is required on each side for installation of the vertical track for standard extension or torsion springs, or
Sideroom: __________________
3.Measure area labeled “headroom”— distance between the top of the door opening (“jamb header”) and the ceiling (or first obstruction, ex: light fixture). 11" is required for standard installation of extension springs; 12" on standard torsion springs and
Headroom needed: ___________
4.Measure area labeled “backroom”— distance is measured from the garage door opening toward the back wall of the garage. Backroom: __________________
Common garage door widths include 8', 9', 16' and 18'. Common garage door heights include 7' and 8'. See Menards Team Member for additional size availability.
NOTE: On 8' and 9' wide doors, a reinforcement strut must be purchased if an automatic garage door opener is installed.
The majority of homes today have automatic garage door openers. Therefore, Ideal doors do not include a lock. If desired, an
CEILING | 4. BACKROOM |
3. HEADROOM
|
| HEIGHT |
|
|
|
|
2. |
|
|
| 2. |
| |
LEFT |
| WIDTH |
|
| RIGHT | |
SIDE |
|
|
|
| SIDE | |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
FLOOR
Headroom/Sideroom Requirements
|
|
|
|
|
| EXTENSION | TORSION | SIDEROOM | |
|
|
|
|
|
| SPRING | SPRING | TORSION SPRING | |
|
| 12" TRACK RADIUS |
|
| 11" | 12" | 12" | 33/4" | |
|
| 15" TRACK RADIUS |
|
| 141/2" | 15 1/2" | 14" | 33/4" | |
|
|
| LOW HEADROOM |
|
| 61/2" | 10" | 91/2" | 6" |
| DOUBLE TRACK (standard) | ||||||||
|
|
|
|
| |||||
| LOW HEADROOM DOUBLE | n/a | 7" | n/a | 6" | ||||
|
|
| TRACK (rear mount) |
|
| ||||
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| TOOLS NEEDED... |
|
|
| |||||
|
|
| Tape Measure |
|
| 7/16", 1/2" & | 9/16" Sockets and Ratchet | ||
|
|
|
|
| |||||
|
|
| Level |
|
| Drill with 3/16", 5/32",3/8" & 7/16" drill bits | |||
|
|
|
|
| |||||
|
|
| Pliers |
|
| Two short pieces of rope about 4' in length | |||
|
|
|
|
| |||||
|
|
| Step Ladder |
|
| Locking Pliers or C Clamps |
| ||
|
|
|
|
|
| ||||
|
|
| Screwdriver |
|
| Two 1/2" x18" Winding Bars (Torsion Springs only) | |||
|
|
|
|
| |||||
|
|
| Saw |
|
| 3/8" | |||
|
|
|
|
| |||||
|
|
| Claw Hammer | All tools may be purchased in Hardware Dept. |
| ||||
|
|
|
| ||||||
|
|
| Sawhorses |
| |||||
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
RESIDENTIAL
GARAGE DOORS
Steel Panel Doors | Carriage House Doors |
|
|
Complete Garage
All steel used in this product is 100% recyclable at the end of its useful life.
Ideal Door®
Ideal Door ® is a brand of Clopay Building Products. Clopay Building Products Company, Inc. 2008
A Griffon Company, Inc.© Printed in U.S.A.
Door Selection
In the interest of better quality and value, we are continually improving |
|
and updating our products. Consequently, photos, illustrations and |
|
available options may sometimes differ from present models. |