ILO DTV2784 owner manual Remote control, Count up 10 minutes each time the button is pressed

							Remote control
			4.	SLEEP Button - To set the TV to turn off after a preset
				amount of time, press the SLEEP button. The clock will
				count up 10 minutes each time the button is pressed in
				the order of 0h00m, 0h10m,...1h50m,2h00m After the sleep
1				time is programmed, the display will disappear then reappear
				momentarily every ten minutes to remind you the sleep
2				timer function is operating. To confirm the sleep time setting,
				press the SLEEP button once and the remaining time will
				be momentarily displayed. To cancel sleep time, press the
				SLEEP button repeatedly until the display turns to 0h00m.
			5.	VOL (VOLUME) + / - Buttons - Press the + button to
	–/			increase, or the - button to decrease the volume level.
3		9		Use to select the desired setting during the menu screen
				operation.
4		10	6.	MENU Button - Press to display the menu screen function.
			7.	EXIT Button - Press remove the menu screen.
		11	8.	TV/AV Button - Press this button to display SOURCE
5				SELECTION menu to select the video input source.
			9.	QUICK VIEW Button - This button allows you to go back
		12		to the previous channel selected by pressing the
6				QUICK VIEW button. Press this button again to return to
7		13		the channel you were watching.
			10.	MUTE Button - To turn off the sound, press this button once.
8
		14		The TV will be silenced and the symbol “MUTE” will appear
	PICTURE	15		on the screen. The muting feature can be released by
	SIZE
		16		pressing the MUTE button again or one of the VOL
				+ or - buttons.
			11.	CH (CHANNEL)		/	Buttons - Press the	button to
				change to a higher numbered channel set into memory.
				Press the	button to change to a lower numbered chan-
				nel set into memory.
				Use to select the desired setting during the menu screen
				operation.

1.POWER Button - Press to turn the TV on. Press again to 12. ENTER Button - Press to enter or select information for

turn the TV off.		On-Screen operations while in the adjustment menu.
2. Direct Channel Selection Buttons (0-9) - Allow direct	13.	RESET Button - Press to reset the menu screen picture
access to any channel.		and sound adjustments to their factory preset positions
3. -/DISPLAY Button - When the TV is receiving an analog		while in the adjustment menu.
signal pressing this button will display the current infor-	14.	CLOSED CAPTION Button - Press this button to display
mation on-screen. When the TV is receiving a digital,		CLOSED CAPTION menu.
pressing this button once will display the digital informa-	15.	AUDIO SELECT Button - Press this button to display
tion on-screen; pressing it a second time will display the		AUDIO menu.
analog information on-screen. To remove the display	16.	PICTURE SIZE Button - Press this button to change
from the screen, press this button again. This button is		the picture size.
also the “-“ button used when selecting digital channels.

Before using the remote control, batteries must first be installed.

ENGLISH

HOW TO INSTALL BATTERIES

1. Open the battery compartment cover.

2. Install two “AAA” batteries.

3. Replace the battery compartment cover.

Use two “AAA” size batteries. The batteries may last approximately one year depending on how much the remote control is used. For best performance, it is recommended that batteries should be replaced on a yearly basis, or when the remote operation becomes erratic. Do not mix old and new batteries or different types.

BATTERY PRECAUTIONS

These precautions should be followed when using batteries in this device:

•Use only the size and type of batteries specified.

•Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed batteries may cause damage to the device.

•Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.

•If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.

•Do not try to recharge batteries not intended to be recharged; they can overheat and rupture (follow battery manufacturer's directions).

7