Installation Instructions |
DISCLAIMER
InFocus and its affiliated corporations and subsidiaries (collectively "InFocus"), intend to make this manual accurate and complete. However, InFocus makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. InFocus makes no representation of warranty, expressed or implied, regarding the information contained herein. InFocus assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.
WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided.
WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. The wall to which the mount is being attached may have a maximum drywall thickness of 5/8" (1.6cm). Do not install drywall anchors into the seam between drywall pieces.
WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components attached to the short throw projector mounts up to (and including) the projector does not exceed 25 lbs (11.34 kg) for the
DIMENSIONS |
|
|
|
|
|
|
|
|
| 32.78" MIN - 58.21" MAX |
| 2.50 | .50 |
| |
|
| TRAVEL 28 - 52.5" | .328 TYP |
| |||
|
|
|
|
| |||
|
|
|
|
|
| ||
|
|
|
| 14.13 | 6.38 |
|
|
|
|
|
|
| 8.38 |
| |
|
|
|
|
|
| 10.38 | 1.42 |
3 | OF |
|
| 13.00 |
|
| |
LEVELING ADJUSTMENT |
|
| 7.56 |
|
|
| |
|
|
|
| 5.73 |
|
|
|
|
|
|
|
|
| 2.52 | 1.09 |
|
|
|
|
|
|
| |
| 5.36 |
|
|
|
| 6.02 |
|
|
|
|
|
|
|
| |
|
|
|
|
|
| 7.40 |
|
57.83 |
| 40.89 |
|
|
|
|
|
| 1.61 |
|
|
|
|
| |
2.28 |
|
|
|
|
|
| |
|
|
|
|
|
|
| |
BOLT CIRCLE |
|
|
|
|
|
|
|
|
| 55.37 |
|
|
|
|
|
40.89 | 2.18 | 110.94 |
|
|
|
| |
1.61 |
| 4.37 |
|
|
|
| |
5.63 |
| THREADS ONTO 1 1/2" NPT |
|
|
|
| |
.22 |
|
|
|
|
| ||
|
|
|
|
|
|
| |
|
|
|
| 168.48 |
|
|
|
|
|
|
| 6.63 |
|
|
|
YAW ADJUSTMENT POINT | 128.88 | PITCH ADJUSTMENT POINT |
|
|
|
| |
10 |
|
|
|
| |||
5.07 | 4 |
|
|
|
|
| |
|
|
|
|
|
| ||
46.20 |
|
|
|
|
|
| |
1.82 |
|
|
|
|
|
| |
|
| ROLL ADJUSTMENT POINT |
|
|
|
| |
|
| 4 |
|
|
|
|
|
|
|
|
|
|
| DIMENSIONS: [MILLIMETERS] | |
|
|
|
|
|
|
| INCHES |
2 | Visit the InFocus support site at www.infocus.com/support |
