Insignia NS-BRDVD3 Selecting the PCM downsampling rate, Turning dynamic range control on or off, Selecting the digital audio output mode, PCM, Off, HDMI, ENTER, ENTER, ENTER

Blu-Ray Disc Player

4	Press		or to select On or Off. Off selects a 60						3	Press	, press or to select Digital Output,
	frames/second output format.									then press ENTER.
5	Press		to go to the previous menu.						4	Press	or to select the digital output mode
Selecting the PCM downsampling rate										you want, then press ENTER. You can select:
										• PCM—Sends mixed digital audio over the
To select the PCM downsampling rate:										HDMI connection in 7.1CH PCM (if supported
										by HDMI device) and the SPDIF connection in
1 Press ENTER. The Settings menu opens.
										two-channel PCM format.
										• Bitstream HD—Sends the original bitstream
				System			Au dio			from the disc over the HDMI and SPDIF
										connections using highest quality possible.
					Network		PCM Downsampling	48 K hz		HDMI has the higher quality capabilities with
					Display		Digital Output	PCM		advanced audio codecs like TrueHD and
							Dynamic Range Control	Off		DTS-HD. Blu-ray audio is limited to the
		Settings
					Audio					soundtrack for the main movie (no PIP audio
				Language						and no effects audio).
										• Bitstream Legacy—Sends the original
			Parental							bitstream from the disc over the HDMI and
										SPDIF connections using legacy audio
										formats. Blu-ray audio is limited to the
2	Press		, press or			to select Audio. The Audio				soundtrack for the main movie (no PIP audio
										and no effects audio).
	menu opens.									• Bitstream mixed—Sends mixed and encoded
3	Press		to select PCM Downsampling, then							Blu-ray audio streams in a single bitstream.
	press ENTER.									This mode is primarily intended for use with
4	Press		one or more times to select the PCM							SPDIF 5.1CH receivers to produce mixed
										Blu-ray audio in surround sound.
	downsampling rate you want. You can select								5
										Press	to go to the previous menu.
	48KHz, 96KHz, or Off.
	• If you have a surround sound amplifier								Turning dynamic range control on or off
		connected to your player through the SPDIF							Dynamic range control is only active when a Dolby
		jack, select the highest sampling rate the
									Digital signal is detected.
		receiver supports. See the documentation that
									When Dynamic Range Control is set to Off, movie
		came with the receiver.
	• If you do not have a surround sound amplifier								soundtracks are played with the standard dynamic

connected to your player, select 48KHz.	range.
	When movie soundtracks are played at low volume
• If you have a surround sound amplifier
	or from smaller speakers, you can set Dynamic
connected to your player through the analog
	Range Control to On. Your player applies
audio L and R jacks, select 48KHz.
	appropriate compression to make low-level content
• If you have a surround sound amplifier
	more intelligible and prevent dramatic passages
connected to your player through the HDMI
	from getting too loud.
output, select 48KHz.

Note

Incorrectly setting the digital audio output’s PCM sampling rate may result in unpredictable audio playback.

5Press to go to the previous menu.

Selecting the digital audio output mode

To select the digital audio output mode:

1Press ENTER. The Settings menu opens.

System	Au dio
Network	PCM Downsampling	48 K hz
Display	Digital Output	PCM
	Dynamic Range Control	Off
Settings

Audio

Language

Parental

2Press or to select Audio. The Audio menu opens.

To turn dynamic range control on or off:

1Press ENTER. The Settings menu opens.

System	Au dio
Network	PCM Downsampling	48 K hz
Display	Digital Output	PCM
	Dynamic Range Control	Off
Settings

Audio

Language

Parental

2Press or to select Audio. The Audio menu opens.

3Press , press or to select Dynamic Range Control, then press ENTER.

4Press or to select On or Off.

5Press to go to the previous menu.

www.insigniaproducts.com 13