Insignia NS-L32Q-10A Legal notices, Specifications, FCC Part, FCC warning, Cables, Canadian notice, Dolby License Notice and Trademark Acknoledgement

Problem

Remote control does not work

Snowy picture or noise

VGA picture is not stable or synchronized

No output from one of the speakers

Control buttons do not work

After images appear

Picture has a few bright or dark dots

Solution

•Press TV (not the color button)

•Replace the batteries. Make sure that the + and – symbols on the batteries align with the + and – symbols in the battery compartment.

•Clean the remote sensor on the front of your TV.

•Bright or fluorescent lighting may interfere with the remote control signal. Turn off the light or move your TV.

•Make sure that the A/V and antenna cables are connected correctly and securely.

•Make sure that you have selected the correct VGA mode on your computer.

•Adjust the balance in the Audio menu.

•Make sure that the Button Lock option is set to Off. For more information, see “Locking control buttons” on page 24.

•Unplug the power cord, wait a few seconds, then plug the cord back in and turn on your TV.

•Do not display a still image, such as a logo, game, or computer image, for an extended period of time. This can cause a permanent after-image to be burned into the screen. This type of damage is not covered by your warranty.

•A few bright or dark dots on an LCD screen is normal. It does not affect the operation of this TV.

Component input (2)	Y: 1 V (p-p), 75 ohm, including sync
	Pr/Cr: ±0.35 V (p-p), 75 ohm
	Pb/Cb: ±0.35 V (p-p), 75 ohm
	Audio: 300 mV (rms)
	Suggested resolutions: 1080i, 720p, 480p, 480i
HDMI input (4)	4 HDMI input jacks
	HDCP compliant
	E-EDID compliant
	Suggested scan rates: 1080i, 720p, 480p, 480i

VGA input	E-EDID compliant
	Suggested scan rates: 640×480 /60 Hz, 800×600
	/60 Hz, 1024×768 /60 Hz, 1360×768 /60 Hz
	Audio input: Headphone mini-jack for stereo
Accessories	Remote control and batteries (2 AA)
	Remote control holder
	AC power cord
	Component cable
	Cleaning cloth
	User guide
	Quick Setup Guide

Legal notices

FCC Part 15

This device complies with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply within the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by

Specifications

Design and specifications are subject to change without notice.

Analog standard	NTSC
Digital standard	ATSC, 8-VSB, Clear-QAM
Screen	32"

Channel coverage	VHF: 2-13
	UHF: 14-69
	CATV: Mid band - A-8 ~ A-1, A ~ I
	Super band - J ~ W
	Hyper band - AA ~ ZZ, AAA, BBB
	Ultra band - 65 ~ 94, 100 ~ 135
Power source	AC 120 V ~ 60 Hz

Power consumption	150 W with TV on
	<1 W in standby mode
Audio power	10 W + 10 W internal speaker
S-Video input	Y: 1 V (p-p), 75 ohm, negative sync

C:0.286 V (p-p) (burst signal), 75 ohm Video/audio input (2) Video: 1 V (p-p), 75 ohm, negative sync

Audio: 300 mV (rms)

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced technician for help.

FCC warning

Changes or modifications not expressly approved by the party responsible for compliance with the FCC Rules could void the user’s authority to operate this equipment.

Cables

Connections to this device must be made with shielded cables with metallic RF/EMI connector hoods to maintain compliance with FCC Rules and Regulations.

Canadian notice

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

“Standard Television Receiving Apparatus-Appareil de reception télévision ordinaire, Canada BETS-7 / NTMR-7”.