2Press or to select SETTINGS. The Settings menu opens.

PICTURE AUDIO CHANNELS SETTINGS

Settings

Parental Controls

Closed Caption

Time

Menu Settings

Input labels

Computer Settings

MOVE

OK

MENU PREVIOUS

EXIT EXIT

ENTER SELECT

Set various TV options

 

 

 

 

 

 

 

Note

You may need to scroll down to see the Reset to

Default option.

3Press to highlight Reset to Default, then press OK/ENTER to confirm.

4Press MENU to go to the previous menu or press EXIT to close the menu.

Programming your remote control

To program your remote to control home theater devices, follow these steps.

Before proceeding, find the codes for the devices you want to program in “Manufacturers’ codes” on page 32 and write them down or highlight them.

To program your remote control:

1Turn on the device (for example, a DVD player) and, if needed, load media such as a DVD.

2Press the device key on the remote for the device that you want to program (TV, DVD, STB, or AUX).

3Press and hold SET until the red LED blinks twice, then release.

4Enter the first five-digit code for the device and brand that you wish to program. The LED blinks once as each digit is entered. If the code is valid, the LED blinks twice.

Note

If the LED does not blink twice, repeat steps 2 to 4 and try entering the code again.

5Aim the remote at the device and press

(power). The device should turn off. If it does not, repeat Steps 3 through 5, trying each code for your brand until you find one that works. If you cannot find a code that works, see “Searching for your code” below.

6Repeat Steps 1 to 5 for the other devices you want to control. For future reference, write down each working device code.

Searching for your code

If your device does not respond to the remote control after trying all codes listed for your brand, or if your brand is not listed, try searching for your code.

To search for your code:

1Turn on the device you want to control.

2Press the desired device key (TV, DVD, STB, or AUX) once.

3Press and hold SET until the red LED blinks twice, then release.

4Enter 9 9 1. The LED blinks twice.

5Press the device group number for your device type (see table below).

•0—Cable (cable converters, video accessories, satellite receivers)

•1—TV (TVs)

•2—VCR (VCRs, DVD players)

•3—Audio (audio amplifiers, audio amps/tuners, CD players)

6Aim the remote at the device and press

(power). The remote sends IR codes from its library to the selected device, starting with the most popular code first. If the device responds, go to Step 8.

7If the device does not respond, press CH and the remote tests the next code for that device

type. Continue to press CH until the device turns off.

Note

Press CH to try the previous code.

8Now that you have found the correct code, press SET to save the code that worked for your device. The LED blinks twice to indicate that the code has been saved.

9To search for other device codes, repeat Steps 1 to 8.

Checking the codes

If you have set up the remote using the procedure in “Searching for your code” on page 29, you may need to find out which five-digit code is operating your equipment.

To find out which code is assigned to your TV (for example):

1Press TV once.

2Press and hold SET until the red LED blinks twice, then release.

3Enter 9 9 0. The LED blinks twice.

4To view the code for the first digit, press 1. Count the red LED blinks (for example, three blinks = 3), then write down the number in the appropriate code listing at the top of this column.

Note

If the LED does not blink, the code digit is 0.

5Repeat Step 4 for the four remaining digits, using 2 for the second digit, 3 for the third digit, 4 for the fourth digit, and 5 for the fifth digit.

www.insigniaproducts.com

29