Insignia NS-LCD19F 19” LCD TV

Appendix

To attach a wall mount bracket to your TV:

1Remove the four M4 screws holding your TV to the stand.

2Secure the wall mount bracket to the back of your TV using the four M4 screws, as indicated in the illustration.

75 mm

M4 screws

Attach wall

 

75 mm

bracket here

 

 

 

 

 

 

 

 

 

Remove M4 screws

 

 

Remove M4 screws

 

 

 

 

 

 

 

 

 

 

Remove stand

Specifications

•Design and specifications are subject to change without notice.

Analog standard

NTSC, PAL M, PAL N

 

 

Channel coverage

Air: 2-69

 

Cable: 1-125

 

 

Power source

AC 110/260 V 50/60 Hz

 

 

Power

<80 W

consumption

<1 W in standby mode

 

 

Audio power

2 W + 2 W internal speaker

 

 

S-Video input

Y:1 V(p-p), 75 ohm, negative sync

 

C:0.286 V(p-p) (burst signal), 75 ohm

 

 

Video/audio input

Video:1 V(p-p), 75 ohm, negative sync

 

Audio:150 mV(rms)

 

 

Component input

Y:1 V(p-p), 75 ohm, including sync

 

Pr/Cr:±0.35 V(p-p), 75 ohm

 

Pb/Cb:±0.35 V(p-p), 75 ohm

 

Suggested resolutions:1080i, 720p,

 

480p, 480i

 

 

VGA input

D-Sub 15-pin terminal

 

E-EDID compliant

 

Suggested scan rates:640×480 /60 Hz,

 

800×600 /60 Hz, 1024×768 /60 Hz,

 

1440×900/60 Hz

 

Audio input: Headphone mini-jack for

 

stereo

 

 

Accessories

Power cord

 

Signal cable

 

Audio cable

 

User guide

 

Remote control

 

Batteries (2 AAA)

 

 

Legal notices

FCC Part 15

This equipment has been tested and found to comply with the limit for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does not cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encourage to try to correct the interference by one or more of the following measures.

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio or TV technician for help.

•Only a shielded interface cable should be used.

Modifications

The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Insignia may void the user’s authority to operate the equipment.

Cables

Connections to this device must be made with shielded cables with metallic RF/EMI connector hoods to maintain compliance with FCC Rules and Regulations.

Canadian notice

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Avis Canadian

Cat apparel numerous de la classed B respected toutes les exigencies du règlement sur le materiel brouilleur du Canada.

Copyright

© 2007 Insignia. Insignia and the Insignia logo are trademarks of Best Buy Enterprise Services, Inc. Other brands and product names are trademarks or registered trademarks of their respective holders. Specifications and features are subject to change without notice or obligation.

www.insignia-products.com

11