This appliance must be grounded. This instant hot water dispenser is equipped with a cord that has a grounding conductor and a grounding pin. The plug must be connected to an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not modify the plug provided with the appliance – if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Check with a qualified electrician or serviceman if you are in doubt as to whether the instant hot water dispenser is properly grounded.
Personal Injury: This tank is a non-pressurized tank. DO NOT modify this system.
DO NOT close vent tube or connect other type dispensers or valves to the tank. Use only the InSinkErator dispenser faucet supplied. Use only parts provided. Contact an authorized InSinkErator Service agent for repairs or replacement components.
Fire Hazard: To minimize possibility of fire, DO NOT store flammable items such as rags, paper or aerosol cans near the tank. DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
Property Damage: To avoid water damage, replace any loose or split tubing. Periodically inspect the unit for any signs of leakage and immediately remove from service any unit suspected of leaking.
An instant hot water dispenser, like any water heater, has a limited life and will eventually fail. To avoid possible property damage, this instant hot water dispenser should be regularly examined for leakage and replaced when necessary. A drain pan, plumbed to an appropriate drain or outfitted with a leak detector, should be used in those applications where any leakage could cause property damage.
WARRANTY INFORMATION
1-Year Warranty
Covers all replacement parts and labor to correct defects in material or workmanship in the dispenser system, for the full warranty period from the date of installation in your home. If warranty service is required during the warranty period, contact an authorized InSinkErator service agent to replace or repair the unit in your home at no cost to you. If your dispenser is
replaced rather than repaired, the warranty on the new unit shall be for the duration of the remaining portion of the original dispenser’s warranty. Note: Warranty is determined by unit serial number and/or date of installation. Purchase or installation receipt may be required to verify warranty status. When service is required, and for the location of your nearest factory authorized service center, call toll free 1-800-558-5700.
The foregoing warranty does not apply to damage or inoperation resulting from accident, alteration, misuse, abuse, improper installation, installation not in accordance with these instructions or local electrical and/or plumbing codes. We do not assume any responsibility for consequential damage. Install using genuine InSinkErator® manufactured components only. Use of non InSinkErator components will void your warranty.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitations of incidental or consequential damages, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Electric Shock Hazard: To prevent electrical shock, disconnect power before servicing unit. Use only a properly grounded and polarized electric outlet.
ADJUSTING THE THERMOSTAT
Factory temperature pre-set is 190˚F.
■ Disconnect power
from unit.
■ To adjust water temperature you’ll
need to access the panel on the front of the tank. Using a screwdriver, turn thermostat screw clockwise to increase temperature or turn counter clockwise to decrease temperature. The cover must always be in place for the thermostate to respond properly.
■After adjusting, depress the dispenser handle for 20 seconds for the water to re-heat to the new setting. If temperature still is not to your liking, repeat the procedure making sure that the handle is depressed for 20 seconds.
Scalding Hazard: Do not allow water to boil. May result in severe burns.
CLEANING THE FAUCET AND TANK
■Only use mild cleaners to clean the faucet and plastic components.
■Cleaners with acids, abrasives, alkaline
or organic solvents will result in deterioration of the plastic components and void
the warranty.
PROPERTY DAMAGE
■Regularly inspect the unit for any signs of leakage. If there are signs of water damage, immediately remove the unit from service.
■To avoid water damage from leakage, replace all cut, loose or split tubing.
■A drain pan, plumbed to an appropriate drain or outfitted with a leak detector, should be used in those applications where any leakage could cause property damage.
SEASONAL STORAGE/DRAINAGE
Anytime the instant hot water dispenser is not used for extended periods of time, unplug and drain unit. If it is below freezing you will need to unplug the unit and drain it.
■Disconnect power from unit.
■Push hot water dispenser faucet lever and allow water to flow until it is cool.
■Shut the cold water flow off at the shut off valve.
■Remove unit from sink and turn upside down to drain.
