User’s Manual

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Item

 

Options

 

 

 

 

Description

 

 

 

 

 

 

 

 

 

Select Enabled if your system has a floppy disk

 

 

 

 

 

Enabled

controller (FDC) installed on the system board

 

 

 

Onboard FDC Controller

 

and you wish to use it.

If you are not going to

 

 

 

 

Disabled

 

 

 

 

 

use FDC or the system has no floppy drive,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

select Disabled in this field.

 

 

 

 

 

 

 

Disabled

 

 

 

 

 

 

 

 

 

 

 

 

 

3F8/IRQ4

 

 

 

 

 

 

 

 

 

 

 

Onboard Serial Port 1

 

2F8/IRQ3

Select an address and corresponding interrupt

 

 

 

Onboard Serial Port 2

 

3E8/IRQ4

for the first and second serial ports.

 

 

 

 

 

 

2E8/IRQ3

 

 

 

 

 

 

 

 

 

 

 

 

 

AUTO

 

 

 

 

 

 

 

 

 

 

 

 

 

IrDA

Select UART2 mode as standard serial port or

 

 

 

UART Mode Select

 

ASKIR

 

 

 

 

IR port.

 

 

 

 

 

 

 

 

 

 

 

Normal

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Hi,Hi

 

 

 

 

 

 

 

 

 

 

 

RxD , TxD Active

 

Hi,Lo

This item allows you to determine the active of

 

 

 

 

Lo,Hi

RxD, TxD level.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Lo,Lo

 

 

 

 

 

 

 

 

 

 

 

IR Transmission Delay

 

Enabled

This item allows you to enable/disable the IR

 

 

 

 

Disabled

Transmission Delay.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Select the value required by the IR device

 

 

 

 

 

Half

connected

to the IR

 

port. Full-duplex mode

 

 

 

UR2 Duplex Mode

 

permits

 

simultaneous

two-direction

 

 

 

 

Full

 

 

 

 

 

 

transmission. Half-duplex mode

permits

 

 

 

 

 

 

 

 

 

 

 

 

 

 

transmission in one direction only at a time.

 

 

 

Use IR Pins

 

RxD2,TxD2

This item

allows you

to determine

the pin

 

 

 

 

IR-Rx2Tx2

 

definition.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Disabled

Select a matching address and interrupt for the

 

 

 

Onboard Parallel Port

 

378/IRQ7

 

 

 

 

278/IRQ5

physical parallel (printer) port.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3BC/IRQ7

 

 

 

 

 

 

 

 

 

 

 

 

 

SPP

Select

an

operating

mode for

the

onboard

 

 

 

 

 

EPP

 

 

 

 

 

parallel

port. Select

Compatible

or Extended

 

 

 

Parallel Port Mode

 

ECP

 

 

 

 

unless you are certain both your hardware and

 

 

 

 

 

ECP+EPP

 

 

 

 

 

software support EPP or ECP mode.

 

 

 

 

 

 

Normal

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EPP Mode Select

 

EPP1.9

Select EPP port type 1.7 or 1.9.

 

 

 

 

 

 

EPP1.7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ECP Mode Use DMA

 

1

 

Select a DMA channel for the port.

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PWRON After PWR-Fail

 

Off

This item is to set whether to run Ac Loss Auto

 

 

 

 

On

 

 

 

 

Restart or off

 

 

 

 

 

 

 

 

 

Former-Sts

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.5.4.4 Watch Dog Timer

 

 

 

 

 

 

 

 

 

 

 

This option will determine watch dog timer.

The choices: Disabled, 1, 2, 4 Min.

ESM-2850 User’s Manual 57