Intel PCM-9387 - page 99

Appendix

System Assignments

This appendix contains information of a detailed

nature. It includes:

• System I/O ports

• 1st MB memory map

• DMA channel assignments

• Interrupt assignments

Contents

Main Page Packing List Model No. List Description Additional Information and Assistance Page Page Contents Chapter 1 Introduction......................................................2 Chapter 2 Installation........................................................ 8 Chapter 3 Chipset Software Installation Utility............22 Chapter 4 Award BIOS Setup.........................................28 4.5 Integrated Peripherals......................................................33 4.6 Power Management Setup...............................................36 4.7 PnP/PCI Configurations.................................................. 38 Chapter 5 PCI SVGA/LCD Setup ..................................42 Chapter 6 Audio Setup.....................................................52 Chapter 7 Ethernet Interface..........................................56 Appendix A Programming GPIO & Waterdog Timer ....68 Appendix B Pin Assignments ............................................74 Appendix C System Assignments......................................88 Appendix D AT/ATX Power setting ..................................92 Appendix E Mechanical Drawings.....................................96 Page General Information Chapter 1 Introduction 1.1 Introduction 1.2 Features 1.3 Specifications 1.3.1 Standard 3.5" Biscuit SBC Functions 1.3.2 VGA/LVDS Interface 1.3.3 Ethernet Interface 1.3.4 Audio Function 1.3.5 Mechanical and Environmental Page Page Installation Chapter 2 Installation 2.1 Jumpers 2.1.1 Jumper Location Label Function 2.1.2 Jumper Settings Page 2.2 Connectors Label Function PCM-9387 Users Manual 12 2.3 Locating Connectors Figure 2.1: Jumpers and Connectors Drawing (component side) Page 2.4 Setting Jumpers 2.5 Installing SO-DIMM 2.6 IDE, CDROM hard drive connector (CN6) 2.6.1 Connecting the hard drive 2.7 Solid State Disk 2.7.1 CompactFlash (CN21) 2.8 Parallel port connector (CN13) 2.9 Keyboard and PS/2 mouse connector (CN14) 2.10 Power & HDD LED Connector (CN10) 2.10.1 Power & HDD LED Connector(CN10) 2.10.2 Power Reset button (S2) 2.11 Power connectors (CN3) 2.12 Audio interfaces (CN2) 2.12.1 Audio connector (CN2) 2.14.2 LVDS LCD panel connector (CN1) 2.13 COM port connector (CN8,CN19) 2.13.1 COM2 RS-232/422/485 setting (J2) 2.15 Ethernet configuration 2.15.1 100Base-T/1000Base-T connector (CN12) 2.15.2 Network boot(Depends on Ethernet Controller) 2.16 Watchdog timer configuration 2.17 USB connectors (CN5,CN9) Page Page Chapter 3 Chipset Software Installation Utility 3.1 Before you begin 3.2 Introduction 3.3 Installing the CSI Utility Page Page Page Page Chapter 4 Award BIOS Setup 4.1 Introduction 4.1.1 CMOS RAM Auto-backup and Restore 4.2 Entering Setup 4.3 Standard CMOS Setup 4.4 Advanced BIOS Features Page Page 4.5 Integrated Peripherals Page Page 4.6 Power Management Setup Page 4.7 PnP/PCI Configurations 4.7.2 Reset Configuration Data 4.7.3 Resources controlled by: 4.7.4 PCI/VGA Palette Snoop 4.8 Password Setting Please Enter Your Password Please Confirm Your Password Page PCI SVGA/LCD Setup Chapter 5 PCI SVGA/LCD Setup 5.1 Introduction 5.1.1 CMOS setting for panel type 5.1.2 Display type 5.1.3 Dual Independent Display Page PCM-9387 Users Manual 44 5.2 Connections to Two Standard LCDs The following tables illustrate typical LCD connection pinouts for the PCM-9387. * LCD connector type: HRS DF 19K-20P-1H or compatible 5.2.1 LG LM 150x06 (1024x768 LVDS LCD) Table 5.1: Connections to LCD/Flat Panel (CN1) 5.2.2 AU M170EG01 (1280x1024 TFT LCD @ 48bit) Table 5.2: Connections to AU M170EG01 (CN1) AU M170EG01 PCM-9387 CN1 Pin Function Pin Function 5.3 Installation of the SVGA Driver 5.3.1 Installation of Windows 98/2000 Page Page Page Page Page Chapter 6 Audio Setup 6.1 Introduction 6.2 Driver installation 6.2.1 Before you begin Page Page Ethernet Interface Chapter 7 Ethernet Interface 7.1 Introduction 7.2 Installation of Ethernet driver 7.2.1 Installation for Windows 98 Page Page Page Page Page Page Page Page Page Page A Appendix A Programming GPIO & Waterdog Timer A.1 Supported GPIO Register A.1.1 GPIO Registers A.1.2 GPIO Example program-1 Page A.2 Watchdog programming Page B Pin Assignments Appendix B Pin Assignments B.1 CPU Fan Power Connector (CN15) B.2 Audio Connector (CN2) B.3 Main Power Connector (CN3) B.4 Keyboard and PS/2 Mouse Connector (CN14) Table B.3: Main Power Connector (CN3) Table B.4: Keyboard and mouse connector (CN14) B.5 IDE Hard Drive Connector (CN6) Table B.5: IDE HDD connector (CN6) B.6 Parallel Port Connector (CN13) Table B.6: Parallel Port Connector (CN13) B.7 Power & HDD LED Connector (CN10) B.8 USB Connector (CN5) Table B.7: Power & HDD LED Connector (CN10) Table B.8: USB Connector (CN5) B.9 LCD Inverter Backlight Connector (CN17) Table B.9: LCD Inverter Backlight Conn (CN17) B.10 LVDS Connector (CN1) Table B.10: LVDS Connector (CN1) DF13A-40DP-1.25V (Hirose Electric Co., Ltd.) B.11 COM2 RS232/422/485 series port (CN8) B.12 CompactFlash Card Connector (CN21) Table B.11: COM2 RS-232/422/485 series port Table B.12: CompactFlash Card Connector (CN21) B.13 IR connetor (CN11) Table B.13: IR Connector (CN11) Table B.12: CompactFlash Card Connector (CN21) B.14 MIO interface (CN4) Page Page Page Page Appendix C System Assignments C.1 System I/O Ports Table C.1: System I/O ports C.2 1st MB memory map C.3 DMA channel assignments Table C.2: 1st MB memory map Table C.3: DMA channel assignments C.4 Interrupt assignments Table C.4: Interrupt assignments Page Appendix D AT/ATX Power setting D.1 Introduction ATX power supply diagram AT power supply diagram