 AGP Aperture Size,  Panel Type,  OnChip USB | Intel SBC-780

F u l l - Size CPU Card	S B C - 7 8 0

AGP Aperture Size

Aperture size will ensure that all writes posted in the global write buffer to the graphics aperture are retired to DRAM before initiating any CPU-PCI cycle. This can be used to ensure synchronization between the CPU and AGP master.

The choices: 128M, 64M, 32M, 16M, 8M, 4M

Panel Type

The choices: 640x480 TFT

800x600 TFT

1024x768 TFT 36bit

1024x768 TFT 18bit

1024x768 LVDS 1 Channel

1024x768 LVDS 2 Channel

800x600 LVDS

Boot Device Select

The choices: Auto, Both

OnChip USB

The choices: Enabled, Disabled.

USB Keyboard Support

The choices: Enabled, Disabled.

USB Mouse Support

The choices: Disabled, Enabled

OnChip Sound

The choices: Auto, Disabled

Chapter3 Award BIOS Setup

3 - 15

Image 53

Intel SBC-780 manual  AGP Aperture Size,  Panel Type,  Boot Device Select,  OnChip USB,  USB Keyboard Support

Contents

SBC-780 Copyright Notice Acknowledgments Packing List Contents Award Bios Setup Driver Installation General Information Introduction Features System Specifications USB Display Quick Installation Guide Safety Precautions I P S Locating connector solder side Mechanical Drawing Mechanical drawing component side Mechanical Drawing solder side List of Jumpers Jumpers List of Connectors Connectors DIMM1 Open Closed Setting Jumpers COM2 RS-232/422/485 Selection JP6&JP7 LCD Voltage Selection JP2Tftlcd Clock Selection JP3 12 COM2 Ring/+5V/+12V Selection JP11 Clear Cmos JP8PCI-104 I/O Voltage Selection JP10 Ttllcd Connector CN2 Optional ATX Power Connector CN1 Ttllcd Connector CN3 Channel 2 Lvds Connector CN5 Channel 1 Lvds Connector CN4 USB2 Connector CN9 USB1 Connector CN8SIR Connector CN6 USB Connectors CN8/CN9 21 COM2 RS-232/422/485 Serial Port ConnectorCN11 LPT Port ConnectorCN10 Floppy ConnectorCN12 Power Connector CN14 / CN15 23 COM1 RS-232 Serial Port Connector CN13 25 PS2 Keyboard/Mouse Connector CN17 VGA Display Connector CN18 CompactFlashä Disk Connector CN21 Audio Input/Output Connector CN24 Internal Keyboard Connector CN22Internal Mouse Connector CN23 Primary/Secondary Hard Drive Connector IDE1&IDE2 Pin Signal Fan Connectors FAN1&FAN2 IDE LED IDE LED+ Front Panel Connector JP5 Award Bios Setup System test and initialization  Major Setup Features  Entering setup Advanced Features Setup  Main Standard Cmos Features  PC Health Setup  Default Load Optimized Defaults Security Password  Save & Exit Setup  Clk/Voltage Setup Exit  Exit Without Saving  Date and Time Configuration  Standard Cmos setupMain Setup  IDE HDD Auto-Detection  IDE Primary/Secondary Master/Slave IDE Primary/Secondary Master/Slave  Drive a  Drive B  Halt On  Video Select Display Device  Base Memory Advanced Features Setup  Virus Warning  Quick Power On Self Test First/Second/Third Boot Device  Boot Up Floppy Seek  Boot Other Device Boot Up NumLock Status  Swap Floppy Drive  Typematic Delay Msec  Typematic Rate Setting Gate A20 Option  Typematic Rate Chars/Sec  OS Select For Dram 64MB  Video Bios Shadow Security Option  Dram Timing By SPD  Advanced Chipset features setup Memory Hole  Frame Buffer Size  AGP Aperture Size  Boot Device Select Panel Type  OnChip USB  OnChip IDE Channel0 / OnChip IDE Channel1  IDE Prefetch Mode Integrated Peripherals  Primary/Secondary Master/Slave Udma  Primary/Secondary Master/Slave PIO Init Display First  Onboard LAN1/LAN2  Uart 2 Mode  IDE HDD Block Mode Onboard Serial Port 1/ Port  IR Function Duplex  Onboard Parallel Mode  Tx, Rx inverting enable ECP Mode Use DMA  Onboard Parallel Port  SB I/O Base Address  Sound Blaster SB IRQ Select  SB DMA Select  Acpi Function  Power Management Setup Power Management  Video off Option  PM Control by APM Video off Method  Modem Use IRQ  Soft-Off by Pwrbtn  State After Power FailureThis option will not be availa Ble when AT power is Applied  Date of Month  Resume Time hhmmss  Primay Intr  PCI Master Choices Enabled, Disabled  Reset Configuration Data  PnP/PCI Configuration PNP OS Installed  Resources Controlled By PCI/ISA PnP IRQ Resources  DMA Resources  Assign IRQ For USB  PCI/VGA Palette Snoop Assign IRQ For VGA Default Setup  Load Optimized Defaults Security Setup  Set/Change password  Shutdown Temperature  CPU Warning Temperature Power on show status PC Health Setup  CPU fan low speed warning  Spread Spectrum 6 Clk/Voltage Setup Auto Detect DIMM/PCI CLK  Exit without saving  Save & Exit SetupExit Setup Driver Installation Applicable for Windows 2000/98/ME/XP Please follow the sequence below to install the driversCd-rom \Driver\ Install VIA 4-in-1 Driver C 7 8 Programming Watchdog Timer Programming Reset CompactFlash Cover Installation Guide Plug in CompactFlash Card How to install the CompactFlash cover C 7 8 Press a little bit with the finger on the hole of the cover Done Pull the cover a little bit from the corner indicated How to disassemble the CompactFlash cover Pull the cover hard from the reverse corner indicated