 Virus Warning,  Quick Power On Self Test | Intel SBC-780 specs

F u l l - Size CPU Card	S B C - 7 8 0

Virus Warning

When enabling this item, you receive a warning message if a program (specifically, a virus) attempts to write to the boot sector or the partition table of the hard disk drive. You should then run an anti-virus program. Keep in mind that this feature protects only the boot sector, not the entire hard drive.

NOTE: Many disk diagnostic programs that access the boot sector table can trigger the virus-warning message. If you plan to run such a program, we recommend that you first disable the virus warning. Before installing Microsoft Windows, please disable this function.

The choices: Enabled, Disabled.

Quick Power On Self Test

Select Enabled to reduce the amount of time required to run the power-on-self-test (POST) while system booting.

The choices: Enabled, Disabled.

First/Second/Third Boot Device

The BIOS attempts to load the operating system from the devices in the sequence selected in these items.

The choices: Floppy, LS120, HDD, SCSI, CDROM, ZIP100, USB-FDD, USB-ZIP, USB-CDROM, USB-HDD, LAN, ISA-FDD, Disabled.

Chapter3 Award BIOS Setup

3 - 10

Image 48

Intel SBC-780 manual  Virus Warning,  Quick Power On Self Test,  First/Second/Third Boot Device

Contents

SBC-780 Copyright Notice Acknowledgments Packing List Contents Award Bios Setup Driver Installation General Information Introduction Features Specifications System USB Display Quick Installation Guide Safety Precautions I P S Locating connector solder side Mechanical Drawing Mechanical drawing component side Mechanical Drawing solder side Jumpers List of Jumpers Connectors List of Connectors DIMM1 Setting Jumpers Open Closed LCD Voltage Selection JP2 Tftlcd Clock Selection JP3COM2 RS-232/422/485 Selection JP6&JP7 Clear Cmos JP8 PCI-104 I/O Voltage Selection JP1012 COM2 Ring/+5V/+12V Selection JP11 Optional ATX Power Connector CN1 Ttllcd Connector CN2 Ttllcd Connector CN3 Channel 1 Lvds Connector CN4 Channel 2 Lvds Connector CN5 USB1 Connector CN8 USB2 Connector CN9SIR Connector CN6 USB Connectors CN8/CN9 LPT Port ConnectorCN10 21 COM2 RS-232/422/485 Serial Port ConnectorCN11 Floppy ConnectorCN12 23 COM1 RS-232 Serial Port Connector CN13 Power Connector CN14 / CN15 25 PS2 Keyboard/Mouse Connector CN17 VGA Display Connector CN18 CompactFlashä Disk Connector CN21 Internal Keyboard Connector CN22 Internal Mouse Connector CN23Audio Input/Output Connector CN24 Fan Connectors FAN1&FAN2 Primary/Secondary Hard Drive Connector IDE1&IDE2 Pin Signal Front Panel Connector JP5 IDE LED IDE LED+ Award Bios Setup System test and initialization  Entering setup  Major Setup Features Advanced Features Setup  Main Standard Cmos Features  Default Load Optimized Defaults  Security Password PC Health Setup  Clk/Voltage Setup  Save & Exit Setup Exit  Exit Without Saving  Standard Cmos setup Main Setup Date and Time Configuration  IDE Primary/Secondary Master/Slave  IDE HDD Auto-Detection IDE Primary/Secondary Master/Slave  Drive a  Drive B  Video  Halt On Select Display Device  Base Memory Advanced Features Setup  Quick Power On Self Test  First/Second/Third Boot Device Virus Warning  Boot Other Device  Boot Up Floppy Seek Boot Up NumLock Status  Swap Floppy Drive  Typematic Rate Setting  Typematic Delay Msec Gate A20 Option  Typematic Rate Chars/Sec  Video Bios Shadow  Security Option OS Select For Dram 64MB  Advanced Chipset features setup  Dram Timing By SPD Memory Hole  Frame Buffer Size  Boot Device Select  AGP Aperture Size Panel Type  OnChip USB  IDE Prefetch Mode  Integrated Peripherals OnChip IDE Channel0 / OnChip IDE Channel1  Primary/Secondary Master/Slave PIO  Primary/Secondary Master/Slave Udma Init Display First  Onboard LAN1/LAN2  IDE HDD Block Mode  Uart 2 Mode Onboard Serial Port 1/ Port  IR Function Duplex  Tx, Rx inverting enable  Onboard Parallel Mode ECP Mode Use DMA  Onboard Parallel Port  Sound Blaster  SB I/O Base Address SB IRQ Select  SB DMA Select  Power Management Setup  Power Management Acpi Function  PM Control by APM  Video off Option Video off Method  Modem Use IRQ  State After Power Failure This option will not be availa Ble when AT power is Applied Soft-Off by Pwrbtn  PCI Master  Date of Month  Resume Time hhmmss  Primay Intr Choices Enabled, Disabled  PnP/PCI Configuration  PNP OS Installed Reset Configuration Data PCI/ISA PnP  Resources Controlled By IRQ Resources  DMA Resources  PCI/VGA Palette Snoop  Assign IRQ For VGA Assign IRQ For USB  Load Optimized Defaults Default Setup  Set/Change password Security Setup  CPU Warning Temperature  Shutdown Temperature Power on show status PC Health Setup  CPU fan low speed warning 6 Clk/Voltage Setup  Auto Detect DIMM/PCI CLK Spread Spectrum  Save & Exit Setup Exit Setup Exit without saving Driver Installation Please follow the sequence below to install the drivers Cd-rom \Driver\ Install VIA 4-in-1 DriverApplicable for Windows 2000/98/ME/XP C 7 8 Programming Watchdog Timer Reset Programming CompactFlash Cover Installation Guide How to install the CompactFlash cover Plug in CompactFlash Card C 7 8 Press a little bit with the finger on the hole of the cover Done How to disassemble the CompactFlash cover Pull the cover a little bit from the corner indicated Pull the cover hard from the reverse corner indicated