COMPONENT WOOFER INSTALLATION INSTRUCTION MANUAL
MOUNTING LOCATION
Carefully select a suitable mounting location for the speaker/tweeter. Be sure to check behind the mounting location selected for adequate space for speaker/tweeter depth. Use the included template if needed
MOUNTING HOLE
SPEAKER : Using a sharp knife or razor, cut the panel using the outline from the template as a guide. Also, drill holes for the mounting screws if installing on metal panels.
INSTALLATION
SPEAKER : Place ABS grill on top of speaker and secure assembly using the self tapping
screw provided. *NOTE : If not using the included grill, grill mount does not have to be installed.
TWEETER : Screw the angle mounting to the location selected or use the double sided tape provided to stick the flush mounting to the location selected.
WIRING
SPEAKER: Carefully route the supplied wire to the speaker, ensuring that it does not pass over any sharp metal edges that will damage the signal path. Connect the terminal ends of the wires to the speakers, watching that the left/right and positive/negative connections are made correctly to the appropriate outputs of the radio or amplifier.
TWEETER : Feed the wires from the tweeter through the flush/angle mounting opening
and connect these wires to the line wires coming from the included outboard crossover tweeter terminals. Push the tweeter into the flush/angle mounting until the tweeter sits nicely into the mounting.
*NOTE : When installing tweeter with flush mount kit, a hot glue gun is sometimes necessary to secure the tweeter's flush mount housing.
INSTALLATION PROCEDURE :
Mounting Holes
Angle Mounting
Speaker Unit
Grill | Screw |
|
Mounting Screws
COMPONENT WIRING DIAGRAM:
EXTERNAL
CROSSOVER
SIGNAL SOURCE UNIT | TWEETER |
|
|
RADIO OR AMPLIFIER | INPUT | WOOFER | |
|
SPECIFICATIONS : |
|
|
|
|
|
MODEL : |
| MODEL : |
|
|
|
5.25" | 6.5" |
|
| ||
Component System |
| Component System |
|
|
|
5.25" Injection PP Mica Cone | 6.5" Injection PP Mica Cone |
| |||
Rubber Surround and |
| Rubber Surround and |
|
|
|
1" Titanium Dome Tweeter | 1" Titanium Dome Tweeter |
|
| ||
with Neodymium Magnet |
| with Neodymium Magnet |
|
|
|
Peak Power Handling | : 300Watts | Peak Power Handling | : 350Watts | ||
Continuous Power (RMS) | : 150 Watts | Continuous Power (RMS) : | 175 Watts | ||
Impedance | : 4 Ohm | Impedance | : | 4 Ohm | |
Magnet Weight | : 10 Oz | Magnet Weight | : | 13 | Oz |
Sensitivity (1W/m) | : 91 dB | Sensitivity (1W/m) | : | 91 | dB |
Freq. Response | : 50Hz - 25kHz | Freq. Response | : | 40Hz - 25kHz | |
Woofer Voice Coil Dia. | : 1" (25mm) ASV | Woofer Voice Coil Dia. | : | 1" (25mm) ASV | |
Fo (Freq. Resp.) | : 92.06 Hz | Fo (Freq. Resp.) | : | 53 | .1 Hz |
Qts (Total Q) | : 0.82 | Qts (Total Q) | : | 0.61 | |
Vas | : 4.1 Lt | Vas | : | 12 | .42 Lt |
Speaker
Tweeter
Double sided
Tape
Flush Mounting
Tweeter
Crossover | : 12dB/Oct | Crossover | : 12dB/Oct |
Interfire Audio Inc. Santa Fe Springs, CA, w w w. i n te r f i re a u d i o. co m