![](/images/backgrounds/52481/52481-1713x1.png)
(110) MODEL 634 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/31/2007
110
GUIDE |
|
|
|
|
|
|
|
|
|
| TROUBLESHOOTING GUIDE | ||||
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
| TROUBLE | CHECK |
| POSSIBLE SOLUTIONS | |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| |
|
| FILTER MOTOR | • Not plugged in. | • Filter cord must be plugged into a 3 wire | |||
|
| FAILS TO START | • Fuse box needs checking. |
| outlet that is protected by a Class A | ||
|
|
|
| • GFCI/RCD circuit breaker |
| Ground Fault Circuit Interrupter, or RCD. | |
|
|
|
| tripped. | • | Reset circuit breaker. If circuit breaker | |
|
|
|
|
|
| trips repeatedly, your electrical system | |
TROUBLESHOOTING |
|
|
|
|
| may have a defect. Turn off circuit | |
|
|
|
|
| breaker and call an electrician to | ||
|
|
|
|
| correct the problem. | ||
|
|
|
|
|
| ||
|
|
|
|
| • Motor too hot and overload protection | ||
|
|
|
|
|
| shut motor off. Let motor cool down. | |
|
|
|
|
|
|
| |
|
| FILTER DOESN’T | • Improper chlorine or pH | • Adjust chlorine and pH level. Consult | |||
|
| CLEAN POOL | levels. |
| your local swimming pool supply stores. | ||
|
|
|
| • Filter cartridge dirty. | • | Clean or replace cartridge. | |
|
|
|
| • Cartridge damaged. | • Check for holes in cartridge. Replace | ||
|
|
|
| • Excessively dirty pool. |
| if damaged. | |
|
|
|
| • Strainer screen restricting | • | Operate filter for longer periods. | |
|
|
|
| flow. | • | Clean strainer screen at pool wall inlet. | |
|
|
|
|
|
|
| |
|
| FILTER DOESN’T | • Inlet/discharge clogged. | • Look for obstructions in intake hose or | |||
|
| PUMP WATER OR | • Air leak on intake line. |
| discharge hose inside pool wall. | ||
|
| FLOW IS VERY | • Scale or buildup on cartridge. | • Tighten hose nuts, check hoses for | |||
|
| SLOW | • Excessively dirty pool. |
| damage, check pool water level. | ||
|
|
|
| • Filter cartridge dirty. | • | Replace cartridge. | |
|
|
|
|
| • Clean cartridge more often. | ||
|
|
|
|
| • Clean inside plunger valve. | ||
|
|
|
|
| • | Pull valve handle to full upright position. | |
|
|
|
|
|
|
| |
|
| PUMP DOESN’T | • Low water level. | • Fill pool to correct water level. | |||
|
| WORK | • Strainer screen plugged up. | • Clean strainer screens at pool inlet. | |||
|
|
|
| • Air leak on intake hose. | • | Tighten hose nuts, check hose for damage. | |
|
|
|
| • Faulty motor or impeller | • Check & clear any sticks or leaves in | ||
|
|
|
| jammed. |
| intake to pump. | |
|
|
|
| • Air lock inside cartridge | • | Turn & pull valve handle to full upright | |
|
|
|
| chamber. |
| position. | |
|
|
|
|
|
|
| |
|
| TOP COVER | • | • Remove cover & check for | |||
|
| LEAKING | • Cover not tight. | • Tighten cover (Manually). | |||
|
|
|
| • Filter cartridge dirty. | • | Replace or clean cartridge. | |
|
|
|
|
|
|
| |
|
| HOSE LEAKING | • Hose nuts. | • Tighten/reinstall hose nut. | |||
|
|
|
|
|
|
| |
|
| AIR LOCK | • Pump housing and inlet hose | • Open air release valves, wait until water | |||
|
|
|
| air trapped. |
| starts to flow out of the air release | |
|
|
|
| • Inlet and outlet hoses |
| valves, close air release valves. | |
|
|
|
| connection reversed. | • Lower position of pool outlet connect | ||
|
|
|
|
|
| to filter pump water inlet, upper | |
|
|
|
|
|
| position of pool inlet connect to filter | |
|
|
|
|
|
| pump water outlet. | |
|
|
|
|
|
|
| |
|
|
|
|
|
| ||
|
|
|
| IMPORTANT |
| ||
|
|
| If you continue to experience difficulty, please contact our |
| |||
|
|
| Consumer Service Department for assistance. See back cover for |
| |||
|
|
| contact information. |
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SAVE THESE INSTRUCTIONS
Page 13