Invacare MK6i specs

9.3.3.2 Adjusting the backrest angle	Position of the metal
	plate

The angle of the backrest is determined by the metal plate with screw-holes, which attaches the backrest to the frame.

The angle can be changed by selecting different combinations of holes between 0°, 5°, 10° or 15° (see drawing).

• Remove the screws that hold the backrest frame on both sides using a 13 Metal plate with holes

mm open-end spanner.

•Select the correct holes for the desired angle using the drawing at right.

•Re-fasten the backrest frame using the hole combination selected.

NOTE:

To make it easier to re-position the screws that hold the backrest, it may be held in place by a second person.

68

Image 68

Invacare MK6i user manual Adjusting the backrest angle Position of the metal Plate

Contents

Invacare Storm How can you get in touch with Invacare? Deutschland Danmark Portugal Table of Contents Seating systems Horn38 Footrests and Legrests Repair Instructions Lifter optionElectrical System 115 118121 126 Introduction Page Important symbols in this manual Type Classification and Area of Use Safety Notes General Safety NotesPage Page Safety information with regard to care and maintenance Safety Information on Electromagnetic Interference Safety Information on Driving and Freewheel Mode Page Safety Information on Wheelchairs with a Lifter Important if Your Wheelchair is Equipped with a Lifter Standstill Driving Safety Information on Wheelchairs with Recaro SeatsMore than 15-30 Most important components Getting out Getting In and OutGetting Driving Before driving for the first time Taking Obstacles Driving up over an obstacle CorrectDriving down off of an obstacle Incorrect Parking and stationary When parking your vehicleDriving up and down gradients Hand brake Re-engaging the motors Pushing the wheelchair by handDisengaging Motors Advanced Control System ACS Main parts of the Joystick Box Pilot lights Pilot Lights on theJoystick Box On the bottom of the joystick box you will find Meaning of the Display Battery Charge DisplayMain components of the Joystick Box Status Display Multi-Purpose DisplayStatus Display ACS Joystick Box monitors the following functions For more information on the individual symbols see .4.2 on Joystick Socket for ProgrammerWith the Joystick 6 you can Socket for Programmer Bus Cable Charging SocketConnection Socket for Supply Cable Bus Cable Switching the Joystick Box ON/OFF Switching on Switching ON/OFFSwitching OFF Operating the Joystick Box Drive Away Interlock Activating the drive-away lockDeactivating the Drive Away Interlock Drive Away Interlock Magnetic Key Lighting / Flashers Horn Hazard FlashersActivating the Hazard Warning Flasher Activating and deactivating the Hazard Flasher Selecting a Driving Mode Driving Mode has 5 levels Shifting up from Driving Mode 1 Switching Driving Modes Switching down from Driving Mode 5 Driving and Steering Driving forwards Forward and BackwardsDriving backwards Braking Cornering Turning on the spot Purpose Display Adjusting electric options using the JoystickJoystick and Multi Select Adjustment Mode Symbol Select symbols Select Adjustment Mode Both Right legrest Legrests Symbols of the Adjustment OptionsLegrest Select Select the option that needs to be adjustedSelect option that needs be adjusted Adjust option Deselect Adjustment ModeAdjust option Symbol on the Multi Troubleshooting on the ACS Control System Error Codes Flashes Flash code Meaning Direct remedy Further action s Flashes Or 10 x flashes Swinging the Joystick Box out to the side option Adjustment Options of the Joystick BoxAdjusting the Joystick Box to length of the arm Adjusting the height of the Joystick Box option Adjusting the height of the armrests Adjusting the seat tilt Manual adjustmentSeating systems Standard and Kontur Seats Electric adjustment Backrest adjustment Page Backrest with electric adjustment option When driving, the backrest angle must never exceed Positioning the headrest Adjusting the headrestHeight adjustment Adjusting the height of the sideframes Seat width adjustment Adjusting the pommel To position the pommel Recaro N-Joy and Miles mechanically adjustable Backrest adjustmentAdjusting the height of the armrests Recaro Seats Recaro Ergomed DS electrically adjustable Invacare Special Seating System Manual adjustment Invacare Ultimate and Personal Special Seating Systems Retainer plate Adjusting the height of the backSeat version Personal Lower slot Page Seat version Ultimate Adjusting the backrest angle Position of the metal Plate Fine adjustment of the backrest angle Letting air out Removing the backrest Upper backrest holders Lower latching mechanism Pull the levers Refitting the backrest With Pre-Adjusted Angle General Information Footrests and LegrestsFootrests Footrest standard Removing the Footrest Footrest Adjusting the Angle Footrest Adjusting the Length Footrest Adjusting the Angle of the Footplate Option Legrests Settable Legrest Option Removing the Legrest Settable legrest Adjusting the Angle Settable legrest Adjusting the Length Settable legrest Adjusting the Angle of the Footplate Manually Adjustable Legrest Removing the Legrest Height Adjustment for Ergonomic Length Compensation Manually adjustable legrest Angle Adjustment Manually adjustable legrest Adjusting the Length Electrically Adjustable Legrest Removing the Legrest Height Adjustment for Ergonomic Length Compensation Adjust left legrest Adjust right legrest Electrically adjustable legrest Angle AdjustmentFlashing symbol shows which legrest can be adjusted Legrest Adjusting the Length Legrest Adjusting the Angle of the Footplate Width Adjustment of the Legrests Option Position of the clamping lever Lifter option Adjusting the seat tilt on a Storm with a Lifter Module To adjust a Recaro Seat see Chap .2 of this manual Adjustment of the electric Lifter Module Speed of the Storm is reduced as follows Technical Specifications of the Lifter ModuleAutomatic speed reduction Electrical System Electronics Protection System Batteries What you need to know about batteriesPage Charging the batteries Charging the batteries Charging Socket of the Joystick Box After contact with eyes Removing and fitting batteriesAfter contact with skin Removing and refitting the 70 Ah batteries Requirements Page Page Removing and fitting the 55 Ah batteries old Storm model Disposing of dead or damaged batteries correctly Lighting Repair Instructions Replacing light bulbsHeadlights Front flasher Tail lights and rear flashers Remove the wheel Repairing a flat tyreRepairing a flat tyre pneumatic tyres type 200 x Repair the flat tyre Repairing a flat tyre pneumatic tyres type Remove the front wheel Repair the flat tyre Remove the wheel Repair the flat tyre Care and maintenance Cleaning the wheelchair Maintenance Jobs Seat and backrest padding Side part and armrestTyres Front wheel forks / Front wheels Electronics / Electrical System Maintenance JobsCleaning Securing the wheelchair for transport TransportTransferring the wheelchair to another vehicle Taxi Bar Anchor ring, lateral Option Crash Kit Option Technical Specifications Seats Electrical System Weight Driving attributes Inspections Performed English