Jacuzzi Faucet Kit installation instructions Preparation, Drilling Holes

Water Rainbow™ Fill Spout/Faucet Kit

Installation Instructions

IMPORTANT: Read all instructions before beginning installation. Consult local codes for requirements.

The Water Rainbow fill spout/faucet kit is designed for installation on most Jacuzzi Whirlpool Bath products or on any bath having sufficient rim space for mounting. The installation procedure requires drilling holes in the bath shell, mounting fittings, and making the proper water supply connections to the faucet valves and fill spout. Hole drilling templates and instructions are provided here for this purpose.

Contents of Kit: Water Rainbow fill spout as- sembly, faucet handles with inserts--hot (red dot) and cold (blue dot), faucet valve assembly (2), 1/4-20 x 1-1/2" hex bolt with/washer and locknut (2), 1-1/2" diameter. push-on speednut (2), faucet handle gasket (2), #10-24 x 3/8" PHPM screw (2), cartridge valve wrench with instructions.

Preparation

Locate the area on the bath or spa rim where the Water Rainbow and faucet valves are to be installed. For separated valve installations, refer to illustrations B and G; for paired valve installations, refer to illustrations C and H.

For installation on all baths, locate the Water Rain- bow fill spout and valves on a level surface which will allow water to clear the rim and flow directly into the bath (see illustration A). Also be certain the fill spout has easy access and that there is adequate space for plumbing connections to the fill spout, both before and after installation. (Refer to plumb- ing instructions regarding top access installation, illustration M.)

Dry fit the Water Rainbow fill spout and valves in the desired area (before drilling holes) to be sure the location is appropriate.

WATER RAINBOW FILL SPOUT

AND FAUCET HANDLES

1/4" MIN.

RIM

INSIDE OF
BATH					LOCATE FILL SPOUT
					ON TOP OF BATH
					RIM TO ALLOW
A					DIRECT WATER
					FLOW INTO BATH
B HOT WATER		HOLE FOR FILL SPOUT				COLD WATER
			2-1/2"	2-1/2"
FAUCET HOLE						FAUCET HOLE
1-1/2" DIA.	15/64" DIA.					1-1/2" DIA.	15/64" DIA.
	9/32" DIA.				9/32" DIA.	1/2"

		1/2"
15/64" DIA.	11/16"	15/64" DIA.
			1-3/8" DIA.
15/64" DIA.			15/64" DIA.	15/64" DIA.
	7"		7"

INTERIOR OF

BATH OR SPA

HOLE DRILLING SCHEME FOR WATER RAINBOW

SPOUT AND FAUCETS - SEPERATE VALVE CONFIGURATION

Drilling Holes

Detach the templates (on back page) and tape them onto the acrylic surface of the bath rim, lo- cating the center lines of the fill spout and valve holes according to appropriate dimensions given in Illustration B or C.

Note: To insure template has been printed to scale, measure the 2 1/2" spacing from center Fill Spout mark and 9/32" hole mark for the 1/4 - 20 Hex Bolt anchors.

C		HOLE FOR		FAUCET
	2-1/2"	FILL SPOUT		HOLES
			1-1/2" DIA.	HOT	COLD
1/2"	15-64"				1-1/2" DIA.
			1/2"
					15/64" DIA.
	9/32" DIA.	2-1/2"		15/64"	11/16"
			9/32" DIA.
	1-3/8" DIA.		7"	3"	15/64" DIA.

INTERIOR OF

BATH OR SPA

HOLE DRILLING SCHEME FOR WATER RAINBOW SPOUT AND FAUCETS - PAIRED VALVE CONFIGURATION

Jacuzzi Whirlpool Bath 6683000G 8/06