Cleaning the Bath | MAINTENANCE INSTRUCTIONS |
Purging the Whirlpool System |
To clean your bath, simply use a mild, nonabrasive liquid detergent solution. You can protect and restore the gloss to a dulled acrylic surface by applying Meguiar's #10 Mirror Glaze, a product specifically designed for use on acrylic finishes. If Meguiar's is not available, an acrylic polish of equal quality or automotive paste wax is acceptable.
Never use abrasive household cleaners on any Jacuzzi Whirlpool Bath product.
NOTE: THE WHIRLPOOL SYSTEM SHOULD BE PURGED AT LEAST TWICE A MONTH
To remove accumulations of bath residue from the whirl- pool system, it is recommended that a whirlpool bath be purged at least twice a month. For best results, however, we recommend that you purge your whirlpool bath after each use using, Systems Clean™, our exclusive
ENGLISH
Repairs to the Surface
Minor scratches which do not penetrate the color finish can be removed by lightly sanding with
Major scratches and gouges which penetrate the acrylic surface will require refinishing. Ask your Jacuzzi Whirlpool Bath dealer for special instructions.
Bath Additives
NOTE: DO NOT USE OIL OR OIL BASED BATH ADDITIVES.
If you want to use any kind of bath additive, use only a small amount of
The use of certain bath oils, bubble baths and bath addi- tives may increase the level of accumulations of bath residue in the whirlpool system. If excess accumulations persist, you should discontinue use of these products.
Spinning Jets Maintenance
(Models equipped with spinning jets)
If hair or other kind of debris gets caught in the bearings of these jets, it could cause them to stop spinning. This may require disassembly and cleaning. To do this, simply grab the nozzle and pull straight out of the jet housing. The bearing casing will be attached to the nozzle. These can be separated by holding the casing and pushing the nozzle out from the rear of the casing. After cleaning, reassemble in reverse.
PUSH FROM REAR
TO REMOVE
NOZZLE
NOZZLE
BEARING CASING
Systems Clean™ is available through an authorized Jacuzzi Whirlpool Bath distributor or by calling us direct at
Systems Clean™ Instructions for use:
Refer to the instructions on the Systems Clean™ packet.
CAUTION: DO NOT USE WHILE BATHING! USE EXTREME CAUTION WHEN HANDLING THIS PRODUCT!
Immediately after bathing and exiting the whirlpool bath, leave the bath water in the tub and add more hot water. The water level in the tub must be at least 2” (5,08 cm)above the highest jet. NOTE: Inducted air from the hydromassage system will cause the Systems Clean™ contents to foam increasing odor. Turn OFF the whirlpool air control or turn it to the lowest setting and pour in the entire contents of PACKET #1 ONLY directly into the bath water. For best results, pour the System Clean into the tub near the intake for the circulation pump and be sure to avoid contact with your skin. Allow the whirlpool to run for 30 seconds and then add PACKET #2 ONLY. It is important to use PACKET #1 before PACKET #2 to avoid a strong odor. Allow the bath to run for 5 to 10 minutes then drain the tub completely. Refill the tub with cold water and run for 2 to 3 minutes. Drain completely and rinse off any residue. Remember to reset the air valves to your bathing comfort level.
DANGER: Harmful if swallowed. Eye irritant. Protect your eyes, skin and mucus membranes from contact with this product or its concentrated solution. A strong alkaline product can cause severe burns to the eyes and skin.
If you have followed the standard purging instructions above and still have an excess accumulation of bath residue and desire an alternative cleaning mechanism, we recom- mend SUPER SYSTEMS CLEAN™ PLUS manufactured by Stearns Packaging to rectify this condition. This may be obtained by contacting us at
23
Jacuzzi Whirlpool Bath K339000X 3/06
