THE PUSH-BUTTON/LED/RECEIVER/ANTENNAASSEMBLY:

The Spread Spectrum Receiver Antenna Assembly provided with this unit allows routing from below the dash board for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception. Special considerations must be made for windshield glass as some newer vehicles utilize a metallic shielded window glass that will inhibit or restrict RF reception. In these vehicles, route the antenna toward a rear window location for best reception. Secure the antenna with double stick tape provided. After securing the antenna with tape, we advise also securing a section of the antenna cable to a fixed support. This will prevent the antenna from dropping down in case the double stick tape is exposed to extreme heat which may loosen it's gummed surface. Route the 6 pin connector toward the control module using caution not to pinch the cable as this will cause poor or no RF reception to the control module.

SHOCK SENSOR:

Select a centrally located, solid mounting surface for the shock sensor that will allow consistent operation from all areas of the vehicle. The selected location must be within 18" of the control module to allow routing and connecting of the 4 pin harness. Secure the shock sensor to the chosen location using two #8 self tapping sheet metal screws. The sensor can also be secured to an existing dash brace using cable tie straps. Whichever mounting method is used be sure to allow access to the sensitivity adjustment potentiometer for use later in the installation.

STARTER INHIBIT RELAY:

Select a mounting location within 12" of the ignition switch's low current start solenoid wire. Secure the relay to an existing harness in the chosen location using a cable tie around the relay's wiring harness. CAUTION! Do not wire tie the metal bracket to an existing wiring harness as vibration may cause

chaffing and shorting damaging the factory wiring. If an existing harness is not available then secure the relay's metal mounting tab to an under dash metal brace with a #8 self tapping sheet metal screw. Wire the relay as per the diagram found later in this manual.

This unit is to be used in vehicles with AUTOMATIC TRANSMISSIONS only! Although this combination Alarm/Remote Start unit is a sophisticated system with many advanced features, IT MUST NOT be installed into a vehicle with a manually operated transmission. Doing so may result in serious personal injury and property damage.

IMPORTANT!

DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MULTI PIN INPUT / OUTPUT HARNESS INTO THE CONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HAVE BEEN MADE. AFTER SELECTING YOUR TARGET WIRES AS DEFINED BELOW, DISCONNECT THE NEGATIVE BATTERY CABLE FROM THE VEHICLE BATTERY PRIOR TO MAKING ANY CONNECTIONS.

NOTE: Do not remove the fuse holders from this wire harness. Fuses must be used and located as close as possible to the power source for adequate protection of the vehicle.

6

128-8843

6 of 28

Page 5 Page 7
Page 6
Image 6
JAMO SS9000 installation manual Push-Button/Led/Receiver/Antennaassembly, Shock Sensor, Starter Inhibit Relay
Page 5 Page 7

SS9000 specifications

The JAMO SS9000 is an innovative sound system that has gained attention for its impressive combination of performance, design, and usability. As part of the JAMO range, this model stands out for its ability to deliver exceptional audio quality while offering advanced features that cater to the modern listener.

One of the main features of the JAMO SS9000 is its state-of-the-art speaker technology. It employs advanced driver designs that ensure clear and precise sound reproduction across a wide frequency range. The system utilizes a combination of woofer and tweeter components to provide a balanced sound profile, making it suitable for various music genres and listening preferences. With its robust construction and high-quality materials, the JAMO SS9000 is built to last while delivering consistent performance.

Another key characteristic of the JAMO SS9000 is its wireless capabilities. The system supports Bluetooth connectivity, allowing users to stream music directly from their smartphones or tablets quickly. This feature enhances user convenience, eliminating the need for cumbersome wires and creating a tidy, uncluttered listening environment. Additionally, the JAMO SS9000 is compatible with various streaming services and devices, making it a versatile addition to any home audio setup.

The design of the JAMO SS9000 is both stylish and functional. Its sleek lines and modern aesthetics make it an attractive piece for any room, blending seamlessly with contemporary decor. Available in different finishes, users can select a color that complements their style and preferences.

Furthermore, the JAMO SS9000 incorporates advanced acoustic technologies that enhance its performance. The system features a sophisticated anti-distortion mechanism that ensures clean sound even at higher volumes. This technology is critical for audiophiles who demand clarity and fidelity in their music.

Overall, the JAMO SS9000 stands out for its combination of impressive audio performance, modern design, and practical features. Whether used for casual listening or more critical listening sessions, this system promises to deliver an exceptional audio experience that caters to the needs of today's consumers. With its robust build quality, wireless capabilities, and aesthetic appeal, the JAMO SS9000 is a worthy consideration for anyone looking to upgrade their home audio setup.
Top Page Image Contents