VM9410

USING THE TFT MONITOR

Open/Close TFT Monitor

Open TFT Monitor

Press the OPEN button (1) on the front panel or press the ( ) button (25) of the front zone remote control to activate the mechanism that moves the display panel into the viewing position.

Close TFT Monitor

Press the OPEN button (1) on the front panel or press the ( ) button (25) of the front zone remote control to load the display panel back into the compartment.

TFT Monitor Auto Open

If “TFT Auto Open” is “on” when the unit is turned on, the monitor automatically moves to the viewing position.

If “TFT Auto Open” is ”off” when the unit is turned on, press the OPEN button (1) or ( ) button (25) on the front zone remote control to move the monitor into the viewing position.

Reverse Driving Use

If the rear-view video camera is connected, the unit is on, and the monitor is stationed inside the main compartment of the unit, the monitor automatically moves into the viewing position and switches to CAMERA mode upon reverse driving. When the reverse driving stops, the monitor returns to the main storage compartment.

If the monitor is in display mode, the monitor automatically switches to CAMERA mode upon reverse driving. When the reverse driving stops, the monitor return to its original input mode.

Monitor Tilt Angle Adjustment

A known characteristic of LCD panels is the quality of the display in relationship to the viewing angle. The monitor angle can be adjusted for optimum viewing using one of the following methods:

Step by Step Angle Adjustment

Press the ( ) or ( ) button (3, 4) on the monitor frame to adjust the tilt angle of the screen one step at a time.

Continuous Angle Adjustment

Press and hold the ( ) or ( ) button (3, 4) on the monitor frame to adjust the tilt angle in a continuous motion.

Aspect Ratio

Press the WIDE button (28) on the remote control or WIDE/ PICTURE button (2) on the monitor to adjust the aspect ratio as follows:

FULL

The entire screen is extended horizontally to the aspect ratio of 16 to

9.The extension ratio is the same at any point.

WIDE

The screen is extened horizontally to the aspect ratio of 16 to 9. The extension ratio increases toward the right and left ends of the screen.

NORMAL

The conventional display image has a 4 to 3 ratio of horizontal to vertical, leaving a blank area on the right and left sides of the display.

Image Setting

Video Output Format

Table 3 shows the video output format for each playing source.

Table 3: Video Output Formats

Playing Source

Video Output Format

 

 

 

 

TUNER

RGB Mode

 

 

DVD

RGB Mode

 

 

AUX IN

CVBS Mode

 

 

CAMERA

CVBS Mode

 

 

*CVBS – Composite Video Baseband Signal

Adjustable Parameters

While in DVD or TUNER mode, the only parameter that can be adjusted is brightness (BRIGHT). To access “PICTURE”, “COLOR”, “CONTRAST”, and “TINT” you must be in AUX or CAMERA mode.

NOTE: The default adjustment is “0” in PAL mode. Tint is unavailable for adjustment.

Parameter Adjustment Procedure

1.Enter Picture Quality Setting mode:

Press the PIC button (24) on the remote or press and

hold the WIDE/PICTURE button (2) on the monitor panel.

2.Select Item to Set:

Press the ( ) ( ) buttons (14, 22) on the remote or press and hold the () or () buttons (18, 19) on the monitor panel.

3.Set Parameters:

Press ( ) ( ) buttons (17, 19) on the remote or press () ( ) buttons (16, 17) on the monitor panel.

4.Exit Picture Quality Setting Mode:

Press the PIC button (24) on the remote or press and hold the WIDE/PICTURE button (2) on the monitor panel.

Parking Brake Inhibit

When the “PRK SW” cable is connected to the brake switch, the display on the TFT monitor will display video only when the vehicle is parked.

Parking cable function is overridden when the video source is set to CAMERA.

When the parking brake inhibit is on, the front monitor displays “Parking Is On”, preventing the driver from watching content while driving. Rear video screens are not affected.

Monitor Movement Mechanism

If an obstruction occurs in the monitor path, the following protective measurements can be executed to prevent damage to the mechanism or monitor:

Table 4: Monitor Protective Measures

Obstruction

Self

OPEN Button

Power

Protection

Pressed

Reconnected

 

 

 

 

 

 

 

 

 

Monitor load-

Monitor is auto-

Monitor fully

Monitor is auto-

ing out hori-

matically

extended hori-

matically

zontally

loaded into unit

zontally

loaded into unit

Monitor load-

Unit stops at

Monitor fully

Monitor is auto-

ing in hori-

obstruction

extended hori-

matically

zontally

point

zontally

loaded into unit

Monitor load-

Unit stops at

Monitor swiv-

Monitor swiv-

ing out verti-

obstruction

els back to the

els back to the

cally

point

unit

unit

Monitor load-

Unit stops at

Monitor swiv-

Monitor swiv-

ing in verti-

obstruction

els back to the

els back to the

cally

point

unit

unit

After the protective procedure is executed, normal operation is resumed by pressing the OPEN button (2) or disconnecting and reconnecting the power.

10

Page 12
Image 12
Jensen VM9410 owner manual Using the TFT Monitor