Jensen VM9512 operation manual Tuner Operation

VM9512

TUNER OPERATION

Tuner TFT Display

8 26 17 1 4 5 10 2 24 253

01:02 PM

	RADIO FM-1		P1	87.5 MHz
		ST	LOC		PTY	RDS
E	P1		87.5	MHz
Q
R	P2		90.1	MHz
E
A	P3		98.1	MHz
R
	P4		106.1	MHz			AS
P
I	P5		107.9	MHz
P
	P6		102.9	MHz
	PS:					BAND	1/2	MEM
27		7			6
9					20
					14
11		AS			12	PTY
13					16			23
	BAND	1/2	PS			MEM	2/2	LOC
	15	19	21			18		22

1.Current radio band indicator

2.Radio frequency indicator

3.Clock

4.Stereo broadcasting indicator

5.Strong Local signal broadcasting indicator

6.Preset radio stations: Touch to recall preset stations

7.RDS Information: PS (Program Service), PTY (Program Type), RT (Radio Text)

8.EQ: Touch to view Spectrum Analyzer > Equalizer

9.Touch to access the direct entry screen

10.Current preset station indicator

11.<<: Touch to seek backward

12.>>: Touch to seek forward

13.: Touch to tune backward one step

14.: Touch to tune forward one step

15.BAND: Touch to change between AM/FM bands

16.AS: Touch to automatically store stations

17.Touch to view the SOURCE MENU and select a new playback source

18.MEM: View screen used to enter current channel into preset memory

19.1/2 or 2/2: Touch this page button to view a second page of on-screen buttons

20.Touch to view the SETUP menu

21.PS (Preview Scan): Touch to scan all stations available, stopping for 5 seconds at each and continuing until a station is selected

22.LOC: Touch to tune to strong local stations

23.PTY: When PTY is pressed, the Program Type categories are listed, allowing listeners to find similar programming by genre. When a PTY category is selected from the touch screen menu, the radio will start scanning for the selected category.

24.Indicates the PTY function is activated

25.Indicates the RDS function is activated

26.REAR: Touch to view the Rear source screen

27.PIP: Touch to view Rear, Front or NAV source

Switch to Radio Tuner source

•Touch the top left corner of the screen (the RADIO circle) to view the SOURCE MENU. Touch “RADIO”.

•Press the SRC button (6) on the front panel or remote control (8) to switch to the AM/FM or RADIO source.

Select FM/AM Band

Touch the BAND button (15) on the screen, or press the BAND button on the unit (4) or remote control (20) to change between the following bands: FM1, FM2, FM3, AM1, and AM2.

NOTE: The BAND button on the unit only works when the TFT is closed.

Seek Tuning

To seek the next higher station:

•Touch the >> button on screen.

•Move the joystick to the right.

To seek the next lower station:

•Touch the << button on screen.

•Move the joystick to the left.

Manual Tuning

To increase or decrease the tuning frequency one step:

•Touch the or buttons on screen.

•Move the joystick left/right.

Direct Tuning

To enter a radio station directly, touch the button or press the GOTO button (21) on the remote control to display the direct entry menu.

FM: _ _ _ . _ MHz

1 2 3

Exit

4 5 6

7 8 9

0Clear

Enter the desired radio station using the on-screen number pad. Press Enter to tune to the selected station. To exit the screen without changing the station, touch Exit. To clear your entry and start over, touch Clear.

Using Preset Stations

Six numbered preset buttons store and recall stations for each band. All six stored stations (P1-P6) for the current band appear on the screen.

Storing a Station

1.Select a band (if needed), then select a station.

2.Touch the on-screen MEM button (18) to open the preset screen.

Mem: _

P1 P2 P3

P4 P5 P6

E x i t

3.Touch the preset number in which you would like to store the current station (or press EXIT to cancel and

20