Chain oil, Fuelling, Min 3 m 10ft | Jonsered CS 2171WH instruction

FUEL HANDLING

Chain oil

•The chain lubrication system is automatic and we recommend the use of special oil (chain oil) with good adhesion characteristics.

•In countries where no special chain oil is available, EP90 transmission oil can be used.

•Never use waste oil. This results in damage to the oil pump, the bar and the chain.

•It is important to use oil of the right grade (suitable viscosity range) to suit the air temperature.

•In temperatures below 0°C (32°F) some oils become too viscous. This can overload the oil pump and result in damage to the oil pump components.

•Contact your service agent when choosing chain oil.

Fuelling

WARNING! Taking the following precautions,

!will lessen the risk of ﬁre:

Do not smoke or place hot objects near fuel.

Always shut off the engine before refuelling.

When refuelling, open the fuel cap slowly so that any excess pressure is released gently.

Tighten the fuel cap carefully after refuelling.

Always move the machine away from the refuelling area before starting.

Clean the area around the fuel cap. Clean the fuel and chain oil tanks regularly. The fuel ﬁlter must be replaced at least once a year. Contamination in the tanks causes malfunction. Make sure the fuel is well mixed by shaking the container before refuelling. The capacities of the chain oil tank and fuel tank are carefully matched. You should therefore always ﬁll the chain oil tank and fuel tank at the same time.

Min 3 m

(10ft)

26 – English

Image 26

Jonsered CS 2171WH manual Chain oil, Fuelling, Min 3 m 10ft

Contents

Operator´s manual KEY to Symbols Key to symbols Contents Personal protective equipment Safety InstructionsMachine′s safety equipment Chain brake and front hand guard Chain catcher Stop switchThrottle lock Right hand guard Checking the front hand guard MufﬂerChecking brake band wear Checking the inertia brake release Chain catcher Stop switchThrottle lock Right hand guard Cutting equipment designed to minimise kickback Cutting equipmentGeneral rules Mufﬂer Some terms that describe the bar and chain Sharpening your chain and adjusting raker clearanceChain General information on sharpening cutting teeth Sharpening cutting teeth Tensioning the chain General advice on setting raker clearanceSetting the raker clearance If the raker clearance is too large Lubricating cutting equipment Checking wear on cutting equipment How to avoid kickbackWhat is kickback? Chain drive sprocket Do not let go of the handles General safety precautions Starting General working instructions Fuel safetyBasic safety rules Transport and storage Terms Basic cutting techniqueGeneral Cutting Limbing Felling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreat Cutting the trunk into logs Felling cut Freeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tension What is WHAT? What is what on the chain saw? Fitting a spike bumper AssemblyFitting the bar and chain Working with the chain Petrol Fuel HandlingFuel Two-stroke oil Min 3 m 10ft Chain oilFuelling Cold engine Starting and StoppingStarting and stopping Warm engine Stopping Carburettor with movement limiters MaintenanceCarburettor adjustment Carburettor without movement limiters Fine adjustment of the idle speed TCorrectly adjusted carburettor Low speed jet L Recommended engine speeds are as follows Idle speed, rpm Starter Air ﬁlter Spark plug Adjustment of the oil pumpWhen making adjustments Mufﬂer Heated handles Centrifugal cleaning TurboCooling system Electrical carburettor heating Below you will ﬁnd some general maintenance instructions Daily maintenance Weekly maintenanceMonthly maintenance Technical Data Technical data Length, inches Pitch, inch Max. number of teeth on Bar and chain combinationsBar Chain EN292-2, Cispr 121997, EN608 EC-declaration of conformityApplies to Europe only Page 1088935-26 ´z*xT¶6U¨ ´z*xT¶6U¨