CONTENTS |
|
Major features | 4 |
Notes on settings and use | 4 |
HANDLING PRECAUTIONS
CONTROLS, INDICATORS AND CONNECTORS
Handling precautions | 4 |
Installation in a rack | 4 |
Controls, indicators and connectors |
|
Front panel | 5 |
Rear panel | 6 |
Menu settings |
|
Setting the menu | 7 |
Sub menu | 7 |
Storing menu settings in memory of this unit | 8 |
Recalling stored menu settings or factory default |
|
settings | 8 |
Entering characters | 9 |
Menu contents | 10 |
Others |
|
Error output | 16 |
Rear panel connectors | 18 |
●Avoid using this unit in places subject to the following conditions:
–direct sunlight
–high humidity and dust
–vibrations
–extreme heat
These conditions can cause problems and may damage the unit.
● Influence of strong electric waves and magnetism |
Noise may appear on the screen when used in places close to a |
transmission antenna, or in places near transformers and motors |
where strong magnetism can occur. |
● This equipment is meant for use exclusively in commercial and |
industrial applications. If used at home, it may cause |
interference with radio and television reception. |
● To save electricity, shut off the power when the unit is not in use. |
● Use the supplied power cable for this unit. |
● Do not place heavy objects such as a television monitor on top of |
the unit. Doing so could cause damage or adversely affect |
Front panel
1 | 2 | 3 | 4 | 5 | |
POWER | STATUS | INPUT | SYNC |
|
|
|
|
|
|
|
|
LOCAL REMOTE
7 | 8 | 9 |
ENTER ESC
MENU
Installing the power cable hook | 18 |
Specifications | 19 |
Supplement | 21 |
Optional software
For optional software, consult your JVC dealer. Using it without formal procedures is illegal.
MAJOR FEATURES
This unit converts
Conversion modes are provided for input NTSC video signals with an aspect ratio of 4:3 (standard), in the letter box format or squeezed.
The delay time for video conversion is added to the embedded audio to synchronize audio and video for output.
Input signal can be cropped (in the 4:3 mode, independently for the left and right sides)
Background color can be set with hue, saturation and lightness.
It is possible to set or show the model name (up to 10 characters).
Each function can be set on the front panel with the LCD. The unit can also be
Menu settings can be saved in memory and loaded from memory.
Four independent memories are provided to store menu settings. Stored menu settings can be recalled as required.
Compact design allows this unit to be installed in a 1U EIA rack.
Color bar output possible.
External reference sync signal input connector
Three video/audio output connectors
Enhancer (contour correction), motion sensitivity, background color, screen horizontal/vertical position and system phase can be adjusted.
Error indication and alarm signal output function
Color correction function (option)
Variable enhancer (option)
NOTES ON SETTINGS AND USE
performance. |
● Do not put any foreign objects into the unit. |
● Do not disassemble the unit or try to modify it. |
● Do not block the ventilation openings. |
● Change the cooling fan about three years after installation of the |
unit. |
● When cleaning the cabinet, wipe it with soft cloth. Do not use |
benzene or thinner as these may deform or discolor the cabinet |
surface. To remove excessive dirt, clean the unit with a mild |
detergent diluted with water, then wipe it with dry cloth. |
● Do not use the unit in an environment exposed to gases |
generated by chemicals or organic solvents. |
INSTALLATION IN A RACK
This unit can be installed in EIA standard rack. Ensure sufficient rack strength by attaching
1.Detach the four feet on the base of the unit.
2.Install the supplied rack mount brackets on both sides of front panel using the four supplied screws (M4).
3.Set this unit on the rack, and fix the rack mount brackets onto the rack using the four supplied screws (M5).
2.Rack mount bracket
| 2. Rack mount |
| bracket |
1. Foot | 2. Supplied |
| screw (M4) x 4 |
| EIA rack |
3. Supplied |
|
screw (M5) x 4 |
|
10
1[POWER] indicator
Lights green when power is supplied to this unit.
2[STATUS] indicator
Normally lights green. Lights orange in the menu setting mode, when the set value is changed or the set data is transmitted to this unit. When the transmission is complete, this indicator lights green again. When errors occur in hardware, etc., this indicator lights red.
3[INPUT] indicator
Normally lights green. When no signal is input, this indicator lights orange. If there is an error in the input signals, this indicator lights red.
4[SYNC] indicator
Normally lights green. If a sync
● For details on error indicators, see page 17.
5Display
●When power is applied, the input/output or screen display mode is shown. (Normal display mode)
Model name:
The model name can be set with the menu (up to 10 characters). In the remote mode, the remote ID number (1 – 31) is shown following the model name.
(e.g.)
B C – D 2 3 0 0
[ D 1 1 0 8 0 4 : 3 ]
Input form Output form Screen conversion mode
Memoranda:
●The screen conversion mode can be selected with menu <Output Mode>. p. 10.
●Output form can be selected with menu <Output>. p. 10.
●When menu <Color Correction> is set to “ON” or <Colorimetry> is set to “OFF”, the normal display changes as follows.
6
6
Press this button to change the set value for a menu item in the menu setting mode.
7[/] button
Press this button to select the menu item in the menu setting mode.
8[ENTER/MENU] button
●In the normal display mode, press this button to engage the menu setting mode.
●In the menu setting mode, press this button to enter the set value for the following menu items. (? is shown.)
Output Mode item Output item Profile Save item Profile Load item
●Use to enter the sub menu. ([ENTER] is shown.)
9[ESC] button
In the menu setting mode, press this button to restore the normal display mode.
Memorandum:
● To use the menu setting, refer to pages 7 to 9.
0[LOCAL/REMOTE] switch
Use to select LOCAL or REMOTE to operate this unit. LOCAL : Set to this position to operate this unit with
the operation buttons on this unit.
REMOTE : Set to this position to
● The factory preset is LOCAL.
●When the menu item <Reference> is set to [INPUT] and there is no SD input signal, output video signals may be distorted. In this
case, input external sync signals and set <Reference> to [BB] or
●When the menu item <Reference> is set to [BB] or
See ‘‘Supplement’’ on page 21.
B C – D 2 3 0 0
[ D 1 / 1 0 8 0 / 4 : 3 ]
Change
●Press the 8 [ENTER/MENU] button to display the item in the menu setting mode.
●If an error occurs in the normal display mode, a description of the error is shown. p. 17.
4 | 5 |
