JVC BC-D2300U manual Menu Settings, Rear panel, Setting the menu, Sub menu

CONTROLS, INDICATORS AND CONNECTORS

Rear panel

1 2 3 4 6 8 9

MENU SETTINGS

You can set various functions on the menu. Settings are stored and automatically activated whenever you turn on the power. Up to four independent menu settings can be stored in the unit’s memory and recalled at any time. You can also restore the default factory settings at any time. The menu is shown on the display.

Setting the menu

[STATUS] indicator Display 3 [] button 2, 5 [ENTER/MENU] button

ON	FUSE	IN	CVBS	Pr	REF		1	2	3
	1.6A(125V)	CN1							HD SERIAL OUT
	FUSE		SDI		LOOP
										OFF ON
					THROUGH	1		1	1
OFF			Y	Pb
AC IN	POWER	OUT				ALARM		REMOTE-IN	REMOTE-OUT	TERMINATE

5 7 10 11 12 13

POWER STATUS INPUT SYNC

LOCAL REMOTE

BC-D2300U HDTV UP CONVERTER

ENTER ESC

		MENU
4 [–] button	4 [+] button

1[AC IN] power input connector

Connect to an AC 120 V, 50 Hz/60 Hz power outlet with

the provided power cable. Attach the provided hook beforehand.  p. 18.

2[POWER] switch

Use to turn the power on/off. When the power is turned on, the indicators and display on the front panel light up.

3Fuse holder

The fuse is built in. For fuse replacement, consult your nearest JVC dealer.

4[SDI IN] connector

Input a SMPTE259M standard SD digital serial signal (NTSC). Compatible with embedded audio signals as well. Embedded 20-bit digital audio with 48 kHz sampling frequency can be input with 4 channels.

5[SDI OUT] connector

Active through output of digital serial video/audio signals input to the 4 [SDI IN] connector is possible.

6[CVBS] connector

Input analog composite signals (NTSC). The optional BC-D231 (D2/analog optional board) is required.

7[Y/Pr/Pb] connectors

Input analog component signals (NTSC) to each connector. The optional BC-D231 (D2/analog optional board) is required.

Note:

●The [CVBS] and [Y/Pr/Pb] connectors are enabled only when the BC-D231 optional board is installed. For details, refer to the BC-D231 instruction manual.

9[HD SERIAL OUT] HD digital serial output connectors (3 lines)

Output SMPTE292M standard HD digital serial signals. Output embedded digital audio signals with 20-bit

48 kHz sampling frequency as 4-channel signals.

0[ALARM] connector ... D-sub 9-pin (male)

●This connector is an alarm output (relay contact) connector. When a problem occurs with this unit, an alarm signal is output.

●When menu switch <Remote Port> is set to “ALARM”, remote operation via the RS-232C is possible.

To remote-control this unit via this connector, set the [LOCAL/REMOTE] switch on the front panel to “REMOTE”.

![REMOTE-IN] connector ... D-sub 9-pin (female)

This connector is the input connector for remote-control device.

Connect this connector to a device conforming to the RS-485 serial interface standard.

Memoranda:

●To use this connector, set menu switch <Remote Port> to “REMOTE-IN”.

●Set the remote ID and remote transmission speed with the menu switches.

●To remote-control this unit, set the [LOCAL/REMOTE] switch on the front panel to “REMOTE”.

@ [REMOTE-OUT] connector ... D-sub 9-pin

(female)

Outputs the control signals input to the ! [REMOTE-IN]

connector or 0 [ALARM] connector as signals conform-

ing to the RS-485 serial interface. Connect this connec-

Normal display

B C – D 2 3	0 0
[ D 1 1 0 8 0 4 : 3 ]

	Press the [ENTER/
Menu display	MENU] button.

		O u t p u t	M o d e
			4 : 3
[/]		Item		Setting
	The [–] button			The [+] button
button is effective.				is effective.
		R e f e r e n c e
				I N P U T
		O u t p u t	M o d e
		L E T T E R B O X ?
				Press the [ENTER/MENU]
				button to enter the value.
				The “?”goes out.
	Normal display			Press the [ESC] button.
		B C – D 2 3 0 0
		[ D 1 1 0 8 0 L B ]

3[] button 6 [ESC] button

1Turn the power of this unit ON.

The model name, input/output and screen display mode are shown on the display (normal mode).

2Press the [ENTER/MENU] button to engage menu setting mode.

● The display shows the menu. The current setting is shown.

3Press the [] or [] button to select the menu item.

4Press the [+] or [–] button to change the setting.

Memoranda:

●When “[” is shown at the right of the display, press the [+] button to change the setting. When “p“is shown at the left of the display, press the [–] button.

●When “?“appears after the value you want to set, press the [ENTER/MENU] button to enter the setting.

●When the setting is changed, the [STATUS] indicator lights orange while the set data is transmitted to this unit. When the transmission is complete, this indicator lights green.

Refer to the next page for details on how to store menu setting contents in memory.

5Press the [ESC] button to end menu setting.

● Your changes are stored in memory and the display returns to

normal.

Note:

If power is turned OFF without pressing the [ESC] button, setting changes are not saved.

8[REF] external reference sync signal input connectors (loop-through)

Input external reference sync signal. As these connectors use a loop-through system, signals input to one connector can be distributed from another connector to the other equipment.

Memoranda:

●When signal distribution is not required or this unit is a terminating device, terminate this unit with the external 75-ohm terminator.

●When the signals input to these connectors are used

as a reference sync signal, set the menu switch <Reference> to “B.B” or “HD SYNC”.  p. 10.

●When the signals input to these connectors are used as a reference sync signal, synchronize the input signal with the reference sync signal so that the V sync is within ±300 µs.

tor to the [REMOTE IN] connector of another device.

Up to 31 devices can be connected in series with this

connection.

#[TERMINATE] switch

This is the terminating switch for remote control signals. With a series connection, set this switch to “ON” when this unit is terminated or control signals from the [ALARM] connector are received.

● The factory preset is “OFF”.

Sub menu

Menu display

	C o l o r C o r r e c t i o n
	O N	[ E N T E R ]
[ENTER/MENU] button
		[ESC] button
Sub menu
	Wh i t e	L e v e l
[/]		0
button
		0

Exact settings for variable enhancer (option), color correction (option) and administration can be done on the sub menu.

1.When setting the variable enhancer or color correction to ON, or selecting administration, [ENTER] is shown on the display. To enter the sub menu, press the [ENTER/MENU] button.

2.Set each menu item in the same way as with the ordinary menu.

3.Press the [ESC] button to go to the upper menu by one.

6 7