JVC BC-D2300U manual Others, Error output contd

See "1.4 About Error Messages"

OTHERS

When an abnormality is detected, error notification is provided by LED illumination, error indication on the display and error output to the [ALARM] connector.

Error output (contd.)

Error indications and output contents

Error output

STATUS INPUT SYNC

1. LED lighting

The [STATUS], [INPUT] or [SYNC] indicator on the front panel lights orange (warning) or red (error), depending on the type of error.

2. Display indication

Error	Error contents	LED	ALARM 1	ALARM 2
indications
Power Error	Abnormality in the power unit	STATUS: Red	Short-	Open
			circuited
Fan Error	Abnormality in the fan motor
Data No-input	No video and audio signal is input.	INPUT: Orange	Open	Open
(warning)

POWER STATUS INPUT SYNC

Error indication

Front panel

BC-D2300U HDTV UP CONVERTER

ENTER ESC

MENU

Display

The first line of the display shows a description of the error. When the menu is displayed, errors are not shown.

Memoranda:

●With LOCAL, the error indication is shown when the error is detected and goes out when the error is no longer detected. With REMOTE, once an error is detected, the indication remains (goes out when the switch is set to LOCAL).

●Error codes with 2 to 6 digits may be shown at the same time. In this case, report the error codes to your JVC dealer.

V. Format Error	Format error of the SDI input signals	INPUT: Red	Open	Short-
				circuited
V. Data Error	Error of video data in the SDI input signal
A. Data Error	Error of audio data in the SDI input signal
REF No-input	No external sync signal is input (note)	SYNC: Red	Short-	Open
			circuited
SD Unlock	Synchronization is not possible due to incorrect
	video input signals
Ref Unlock	Synchronization is not possible due to incorrect
	external sync signal input

Fa n		E r r o r
[ D 1		1 0 8 0			4 : 3 ]
V. D a t a E r r o r 0 3
[ D 1		1 0 8 0			4 : 3 ]
						Rear panel
ON	FUSE	IN	CVBS	PrREF	1	2	3
	1.6A(125V)	CN1					HD SERIAL OUT
			SDI	LOOP
				THROUGH			OFF ON
OFF			Y	Pb
AC IN	POWER	OUT			ALARM	REMOTE-IN	REMOTE-OUT TERMINATE

1 5

69

ALARM

3. [Alarm] connector output

2-line alarm output terminals are provided for the rear panel’s [ALARM] connector. Terminals A and B are short-circuited (relay contact) when an error occurs or the power is turned off. Normally, these terminals are open. (For open and short-circuited conditions, refer to the table on the next page.)

The maximum rated value is 30 V 0.5 A for AC/DC with non- inductive load.

Pin assignment of the [ALARM] connector

Pin	Name	Contents
number
1	NC	Unconnected
2	(RD)	(Reception data for maintenance)
3	(SD)	(Transmission data for maintenance)
4	ALARM2-B	Alarm output 2 B terminal
5	GND	Signal ground
6	ALARM2-A	Alarm output 2 A terminal
7	ALARM1-A	Alarm output 1 A terminal
8	ALARM1-B	Alarm output 1 B terminal
9	NC	Unconnected

Comm Error	Abnormal remote communication	STATUS: Red	Short-	Open
			circuited
Device Error	Abnormality in the internal device
——	Power is turned off.	——	Short-	Short-
			circuited	circuited

Note: When an incorrect external sync signal is input, the REF No-input error indication may be shown.

When an error indication is shown, check the input signal and connections according to type of error indicated. When this unit malfunctions, consult your nearest JVC authorized service agent.

on page 1-3.

16 17