– Status display – | (continued) | |||
3 2 K C H – 1 / 2 | S P 0 0 0 m i n |
| 5 |
|
|
| |||
ON-SCREEN DISPLAY – Event display –
Event display : When a specific function is in activation or when the operation status is changed with the remote controller, etc, the events will be displayed at the positions shown below.
0 4 | / 0 1 | / 0 2 |
| S T A N D B Y | - | O F F | 4 | ||
1 1 | : 2 0 | : 0 0 | T C R | 0 2 | : 0 0 | : 0 0 | : 0 0 |
| |
|
|
|
| 3 |
|
|
|
|
|
3 2 K | C H – 1 | / 2 |
| S P | 0 0 0 m i n | ||
A |
|
| B L A N K | S E A R C H |
| ||
B |
|
| I N D E X | D E T E C T E D |
| ||
0 4 | / | 0 1 | / 0 2 |
|
| S T A N D B Y - O F F | |
1 1 | : | 2 0 | : 0 0 | T C R | 0 2 : 0 0 | : 0 0 : 0 0 | |
Display | Contents |
AUDIO OUT | The standard level of the |
LEVEL NORM | playback or EE audio level is |
AUDIO OUT | set to NORMAL or ATT with |
the remote controller. | |
LEVEL ATT |
|
AUDIO OUT | The playback audio channel is |
AUDIO OUT | set to CH1/2, CH3/4 or MIX |
with the remote controller. | |
AUDIO OUT MIX |
|
No. | Item |
3 | Time code |
|
Content
•It displays the time codes (hour, minute, second and frame).
During playback, the time codes recorded on the tape are displayed.
Display at position A
...Operation in progress
DISPLAY ON
The
TCR | : time code reader data |
TCG | : time code generator data |
DTCG : time code data input from a DV IN terminal | |
•The symbols for the second and frame differ according to the framing modes. (NTSC only)
00 | : 00 | : 00 | : 00 |
¥ dot (.) is used for a dropped frame. |
colon (:) is used for a |
frame. |
Display BLANK SEARCH INDEX + 1
INDEX MARK
Contents Blank search in progress.
Index search in progress. The number indicates the index search position.
When an index is written on the tape during recording.
DISPLAY AUTO
DISPLAY OFF
The
The
• The time code display position can be set via the COUNTER |
POSI. item of the DISPLAY menu. |
• The TIME CODE item can be set to turn on/off the time code |
display. |
Display at position B
...Display for about 3 seconds
FIELD STEP | Field by field advance play- |
| back is selected with the re- |
| mote controller. |
4 | VTR operation mode |
|
5 | Remaining tape |
| |
| Memo |
| If the display position of the time |
| code is set to the upper right, |
| this item will be displayed on the |
| lower right |
• The user’s bit is not displayed. |
It displays the VTR operation modes, including: PLAY, EJECT, FF, REW,
When SHTL or JOG is displayed, the speed will also be dis- played at the same time.
•The VTR MODE item of the DISPLAY menu can be set to turn on/off the VTR operation mode display.
It displays the remaining tape duration (minutes). If it is not identified, “ – – – ” is displayed.
•The TAPE REMAIN item in the DISPLAY menu can be set to turn on/off the remaining tape duration display.
•The SP display disappears when the DVCAM cassette is being played back.
•Please use the remaining tape time as a gauge.
Display | Contents |
INDEX DETECTED | Index is found during an in- |
| dex repeat operation. |
VIDEO END | Video end is found during a |
DETECTED | video end repeat operation. |
AUDIO MUTING | Audio is muted with the re- |
ON | mote controller. |
AUDIO MUTING | Audio is |
OFF | remote controller. |
1ST FIELD STILL
2ND FIELD STILL
FRAME STILL
When still or frame advance playback is selected with the remote controller, the type of still image is displayed.
•1st FIELD STILL
•2nd FIELD STILL
•FRAME STILL
20 | 21 |
