OTHERS | – Warning display – |
When an anomaly occurs, this unit automatically identifies the cause and displays an error- | |
coded warning message on the monitor. | |
If the unit is in a state needing rectification, or if an operation error has occurred, an alarm | |
display will be shown on the monitor. | |
For servicing
→Refer to the servicemanual page.
Warning display (Displayed regardless of the DISPLAY mode)
When a warning display appears, this unit stops operation and cease to accept any opera- tion commands. When TAPE DEFFECTIVE (5605 - 5609) is displayed, the unit similarly stops operation but accepts one command, viz EJECT.
Warning display | Alarm display |
Display | Status |
CONDENSATION | Condensation |
ON DRUM |
|
Action
Please leave the power on and wait for the display to disappear.
3 2 K
C H – 1 |
W |
D R U M |
/ 2
A R N I N M O T O
S P
G7 0 0 1 R F A I L U
00
R E
0
m i n
3 2 K | C H | – 1 / 2 |
H E A D | C L E A N I | |
| S P |
N G | R E Q U |
00
I R
0
E
m i n
D !
WARNING 3200 | Unable to load tape |
LOADING FAILURE |
|
WARNING 3300 | Unable to eject tape |
LOADING FAILURE |
|
This error can be resolved by restarting the unit. However, doing so may dam- age the tape in some cases. Please consult your JVC authorized dealer.
0 4 | / | 0 |
1 1 | : | 2 |
1 | / | 0 2 |
0 | : | 0 0 |
T C
R | S T A N D |
0 2 : 0 0 |
BY : 0
- 0
O F F : 0 0
0 4 | / | 0 1 | / | 0 2 |
|
1 1 | : | 2 0 | : | 0 0 | T C |
R | S T A N D |
0 2 : 0 0 |
BY : 0
- 0
O F F : 0 0
WARNING 4100 | Eject error |
|
CASSETTE |
|
|
EJECT FAILURE |
|
|
DEFECTIVE | Tape is cut | Press the EJECT button and retrieve the |
TAPE! |
| cassette. |
5605 - 5609 |
| Then replace the tape. |
WARNING 5702 | Tape ending sensor error | This error can be resolved by restarting |
Alarm
display (Displayed regardless
of the DISPLAY mode) |
TAPE END DET. | the unit. However, doing so may dam- |
ERROR! | age the tape in some cases. Please |
Display | Status | Action |
LOW VOLTAGE | The DC power voltage is low. | Please check the power voltage. |
| The unit will eventually go into the OPERATE |
|
| OFF mode if operation is continued. |
|
consult your JVC authorized dealer. |
WARNING 5802 Tape begin sensor error |
TAPE BEGIN |
DET. ERROR! |
WARNING 7001 Drum rotation error |
DRUM MOTOR |
HEAD CLEANING REQUIRED!
The video head is dirty. If the head is clogged, it will be detected and the alarm message will be displayed during the PLAYBACK mode. When the STOP mode is engaged or when the cas- sette is ejected, the display will go off. When the head clog is cleared, the message will disappear.
Please clean it with the dedi- cated
FAILURE |
|
WARNING 7101 Capstan rotation error | |
CAP MOTOR |
|
FAILURE |
|
WARNING7202 - | Supply reel rotation error |
7203 |
|
SUPPLY REEL |
|
FAILURE |
|
OVER HEATING! The internal temperature of the unit has ex- | Please disconnect the power |
ceeded the regulated value. | and place the unit in a cool |
| place. If this message is dis- |
| played again, the unit may have |
| been damaged. Please consult |
| your JVC authorized dealer. |
• For alarm displays resulting from operation errors, please refer to page 22. | |
66
WARNING7302 - | Take up reel rotation error. |
7303 |
|
TAKE UP REEL |
|
FAILURE |
|
WARNING7305 | Tape winding error during unloading |
TAKE UP REEL |
|
FAILURE |
|
WARNING 7401 Reel motor rotation error | |
REEL MOTOR |
|
FAILURE |
|
Memo This unit uses a microcomputer. It may not function correctly if there is external noise. If this happens, please turn off the power and then on again.
67
