42
12-2 Other problems
Action
Set the [REMOTE] switch to LOCAL.
Set the No. 002 <OPERATION LOCK>
menu switch to OFF.
Connect the monitor to the [MONITOR
OUT] connector.
Set the No. 500 <ON SCREEN> menu
switch to ON.
Read the instructions on page 5 and
clean the heads.
———
Press the [MENU] button and restore the
normal mode.
Causes
The [REMOTE] switch is set to RE-
MOTE.
The No. 002 <OPERATION LOCK> menu
switch is set to ON.
The monitor is not connected to the
[MONITOR OUT] connector.
The No. 500 <ON SCREEN> menu switch
is set to OFF.
The heads are dirty.
The counter does not run on a non-
recorded section of the tape.
The menu switch setting mode is en-
gaged.
Symptoms
The VCRs controls are not
functioning.
On-screen display does not
come up.
Noise appears on parts of
the playback picture.
Tape counter does not run.
13-1 Optional equipment
SA-K46 RS-232C interface board
With this board connected to this unit and a personal
computer, you can control the VCR from a personal
computer. Use a reverse-type cable. For installation and
uninstallation, consult your JVC dealer.
RM-G30 wired remote control
This remote control allows you to control all basic VCR
operations such as PLAY, RECORD, PAUSE, FF, etc.
YC video cables
These cables are used to transmit YC video signals.
The following types are available.
Types Input Output Length
VC-G30U 4-pin 4-pin 3 m
VC-G50U 4-pin 4-pin 5 m
VC-G3030 4-pin 7-pin 3 m
VC-G2030 7-pin 4-pin 3 m
VC-G2050 7-pin 4-pin 5 m
VC-G8030U remote extended cable
This extended cable is for use with the RM-G800 remote
controllers. The cable length is 3 m.
13 APPENDIX
12 TROUBLESHOOTING
43
14 SPECIFICATIONS
5
Audio input
Line : 8 dBs, 10 k, unbalanced
Mic : 67 dBs, 3 k, unbalanced
5
Audio output
Line : 8 dBs, 1 k, unbalanced
Headphone : infinity to 17 dBs, 8 ,
unbalanced
[Time code]
5
Output : 0 ± 3 dBs, low impedance, unbalanced
[DV interface]
5
Input/output: IEEE 1394
[Connectors]
5
RS-422 interface: D-sub 9-pin
5
JVC bus
connector : DIN 12-pin
Accessory
AC cable x 1
Option
SA-K46U RS-232C interface board
Design and specifications subject to change without notice.
Dimensions (unit: mm)
General
5
Power
requirements : AC 120 V (U MODEL),
AC 220 240 V (E MODEL),
50/60 Hz, DC 12 V (10.5 V to 17 V)
5
Power
consumption : 27 W (U MODEL)
:250 mA (E MODEL)
5
Dimensions : (W) 212 mm x (H) 88 mm x (D) 325 mm
(8-3/8 x 3-1/2 x 12-13/16)
5
Weight : Approx. 3.6 kg (7.9 lbs.)
5
Temperature
Operating : 5°C to 40°C (41°F to 104°F)
Storage : 20°C to 60°C (-4°F to 140°F)
5
Humidity
Operating : 30% to 80% RH
5
Format : MiniDV format
5
Signal format : NTSC
5
Usable tape : MiniDV tape
5
Tape width :6.35 mm
5
Tape speed :18.812 mm/s (SP mode) (U MODEL)
:18.831 mm/s (SP mode) (E MODEL)
5
Record/play
time : 60 minutes (with an M-DV60ME
tape, only in the SP mode)
5
FF/rewind time : Within 120 s (with an M-DV60ME
tape)
[Video]
5
Video signal
recording
format :8-bit, 13.5 MHz, 4:1:1 component
recording (U MODEL)
:8-bit, 13.5 MHz, 4:2:0 component
recording (E MODEL)
5
Video inputs
Analog composite: 1.0 V (p-p), 75
Analog Y/C : Y: 1.0 V (p-p), 75
C: 0.286 V (p-p), 75 (U MODEL)
: 0.3 V (p-p), 75 (E MODEL)
Analog component:Y: 1.0 V (p-p), 75
R-Y/B-Y: 0.7 V (p-p), 75
5
External sync
input : 1.0 V (p-p), 75
5
Video output
Analog composite: 1.0 V (p-p) (setup can be switched
ON/OFF with a menu switch), 75
Analog Y/C :Y : 1.0 V (p-p) (setup can be
switched ON/OFF with a menu
switch), 75
C:0.286 V (p-p), 75 (U MODEL)
: 0.3 V (p-p), 75 (E MODEL)
Analog component: Y:1.0 V (p-p) (setup can be
switched ON/OFF with a menu
switch), 75
R-Y/B-Y: 0.7 V (p-p), 75
5
Horizontal
resolution : 500 lines or more
[Audio]
5
Audio signal
recording format: 16-bit, 48 kHz for two channels or
12-bit, 32 kHz PCM for four channels
5
Frequency
response : 20 Hz to 20 kHz (48 kHz, 16 bits)
PHONES MIC
REMOTE
LOCAL
EJECT
OPERATE
REC LEVEL
CH-2/4
CH-1/3
SHIFT
SET
SELECT
SHIFT
MENU
HOLD
AUDIO
MONITOROUTPUT COUNTER
SHIFT A. DUB
ADVANCEPRESET
L CTL
TC
UB
CH-1/2
CH-3/4
R
MIX MIX
REWSTOP FF
RECPLAY
PAUSE
ON/OFF
VIDEO CASSETTE RECORDER BR-DV600U
325
33
51
27
212
27
88