Manuals / Brands / Home Audio / Stereo System / JVC / Home Audio / Stereo System

JVC CA-VSDT8, SP-VSDT8, VS-DT8 Connecting the Speakers

1 32

Download 32 pages, 1.82 Mb

6

Getting Started

CAUTION:

• Make all connections before plugging the System into an AC power outlet.

• Handling the speakers

As this is a precision instrument, handle it carefully so as to protect it from shocks.

Connecting the Speakers

These speakers are exclusively for this system. Using with other devices will damege the speakers.

1. Open each of the terminals to connect the speaker wire leads.

2. Connect the speaker cords between the Speaker terminals of the Unit and the terminals of the Speakers.

Connect the cords with a black line to the (–) terminals and cords without a black line to the (+) terminals.

3. Close each of the terminals to securely connect the cords.

• Since both speakers are the same, you can put either one to the right or left side.

• Do not connect other speakers to the Unit. The difference of the load impedance causes failures.

• Do not use the supplied speakers in parallel with other speakers.

CAUTION:

• Although the speaker SP-VSDT8 has internal magnetic shielding, a TV may display irregular

colors if located near the speakers. If this happens, set the speakers away from the TV.

Removing the speaker grilles

The speaker grilles can be removed.

When removing:

1. Pull the bottom towards you with your fingers.

2. Also pull the top towords you.

When attaching the speaker grilles:

Attach the speaker grilles as shown in the diagram.

SPEAKER IMPEDANCE 4 16

SPEAKERS

RL

Right side (rear view) Left side (rear view)

Marked with a black line

Speaker

grille

(SP-VSDT6) (SP-VSDT8)

Speaker

grille

(SP-VSDT6) (SP-VSDT8)

VS-DT6-8(J)_EN.book Page 6 Monday, January 21, 2002 5:05 PM

Contents

Main COMPACT COMPONENT SYSTEM VS-DT6-8(J)_EN.book Page 1 Monday, January 21, 2002 5:05 PM For Customer Use: VS-DT6/VS-DT8 SP-VSDT8 SP-VSDT8 CA-VSDT8 Consists of CA-VSDT6 and SP-VSDT6 Consists of CA-VSDT8 and SP-VSDT8 CA-VSDT6 SP-VSDT6 SP-VSDT6 Warnings, Cautions and Others / Mises en garde, prcautions et indications diverses (For U.S.A) INFORMATION G-2 For Canada/pour le Canada For Canada/pour Le Canada CAUTION ATTENTION Introduction Features How This Manual Is Organized WARNINGS IMPORTANT CAUTIONS Table of Contents Getting Started Accessories How To Put Batteries In the Remote Control Handle batteries properly. Make all connections before plugging the System into an AC power outlet. Connecting the FM Antenna Rear Panel of the Center Unit Using the Supplied Wire Antenna Using the Coaxial Type Connector (Not Supplied) A 75 antenna with coaxial type connector should be con- nected to the FM 75 COAXIAL terminal. If reception is poor, connect the outdoor antenna. Connecting the AM Antenna Rear Panel of the Center Unit VS-DT6-8(J)_EN.book Page 5 Monday, January 21, 2002 5:05 PM AC IN Screw (not supplied) Turn the loop until you have the best reception. Connecting the Speakers Removing the speaker grilles When removing: When attaching the speaker grilles: Connecting a Subwoofer Connecting External Equipment Connecting an MD Recorder, etc (Digital Output) Connecting the AC Power Cord Installing the Unit on the Stand Installing the Equipment on the Wall Attachment to a wall Location of attachment to a wall Example of attachment (Center Unit) Changing the Display and Control Buttons Settings Be sure to turn off the System when changing the settings. Set the DISP.SET switch to H. Set the DISP.SET switch to V. Example of attachment (Speakers) (SP-VSDT6 only) Using the Remote Control COMPU Play On the Remote Control On the Unit Basic Operations Turning the Power On and Off Turning the System On Turning the System Off Adjusting the Brightness (DIMMER) When the System is Turned On 1 tem. 2 Control. 3 1 on the Remote Control. 2 on the Remote Control to adjust the bass level. TREBLE Control 1 on the Remote Control. 2 on the Remote Control to adjust the treble level. Showing the Time (DISPLAY) Using the Tuner One Touch Radio Tuning In a Station 1 2 1 2 tune in a station. 3 4 Using the CD Player To Insert a CD 1 2 label side front or up as shown below. 1 2 To Select a Track or Passage within a Track Search Play Programming the Playing Order of the Tracks 1 2 3 4 5 6 7 To Modify the Program 1 Remote Control until the RANDOM indicator lights. 2 Repeating Tracks Child Lock Using External Equipment Listening to External Equipment 1 2 Recording the Systems Source to External Equipment Using the Timers Setting the Clock 1 2 Remote Control. 3 1 2 3 4 5 6 the music source selected in step 3. 7 tem. Setting the SLEEP Timer Care And Maintenance Compact Discs General Notes Cleaning the unit Moisture Condensation Troubleshooting Page Page Specifications Amplifier 105.5 mm 140 mm 237 mm