JVC DR-DX5SE Digital Audio Dubbing, INPUT, SAT S-VIDEO:, DECODER:, 8F-1INPUT ^ VIDEO / S-VIDEO VIDEO:

Start playback slightly before the actual point from where you wish to start dubbing.

Perform steps 1 and 2 of A L-1 Output And L-1 Input Setting B (A pg. 63).

64 EN EDITING

SAT S-VIDEO:

Digital Audio Dubbing

If a connected satellite receiver’s output is compatible with Y/C

signals, set to A SAT S-VIDEO B. (For connection, be sure to use

You can dub selected audio from a DVD or Audio CD disc to a

a 21-pin SCART cable that is compatible with the Y/C signal.)

DECODER:

digital audio device.

However, it is not possible to dub copy-protected discs.

To use a decoder connected to the [L-2 IN/DECODER]

connector.

● Turn on the TV and select the AV mode.

NOTES:

● Slide the TV/CABLE/SAT/DVD switch to DVD.

● If you have a satellite receiver or a decoder connected to the [L-2

IN/DECODER] connector, be sure to set A L-2 SELECT B back to

Example: Dubbing to an MD

appropriate mode after editing.

● If you are not connecting a satellite receiver or a decoder to the

Recorder

[L-2 IN/DECODER] connector, leave A L-2 SELECT B set to

A VIDEO B.

● When A L-2 SELECT B is set to A SAT VIDEO B and A SAT

S-VIDEO B, A SAT B appears on the TV screen or front display

panel instead of A L-2 B.

● If A L-1 OUTPUT B is set to A SCART S-VIDEO B, it is not possible

to set A L-2 SELECT B to A DECODER B or A SAT VIDEO B.

● If A L-1 OUTPUT B is set to A SCART RGB B, it is not possible to set

Digital audio device

A L-2 SELECT B to A DECODER B or A SAT S-VIDEO B.

(MD deck, etc.)

● If A L-1 OUTPUT B is set to A COMPONENT B and A L-2 SELECT B

to A SAT VIDEO B, A SAT S-VIDEO Bor A DECODER B, be sure to

connect the [L-1 IN/OUT] connector with a TV.

Coaxial cable

Optical cable

● If A L-2 SELECT B is set to A SAT S-VIDEO B, be sure to set A L-1

(not supplied)

OUTPUT B to A SCART S-VIDEO B.

● The S-Video output does not support the satellite receiver

function. Make use of the L-1 output when viewing images from

To [DIGITAL AUDIO

the satellite receiver.

OUT (COAXIAL)]

OUT (OPTICAL)]

Player

F-1 Input Setting

Set A F-1 INPUT B to the appropriate mode depending on the connector (VIDEO or S-VIDEO)being used on the front panel.

2Press selection keys to select

ENTER.

3Press selection keys to select the appropriate setting, then press ENTER.4Press SET UP to complete the setting.

A F-1 INPUT B, then press

DVD VIDEO SET UP				HDD/DVD/DV SET UP	FUNCTION SET UP			INITIAL SET UP
	REC/PLAY SET UP			DISPLAY SET	VIDEO IN/OUT

		MONITOR TYPE				4:3LB
		F-1 INPUT
							VIDEO VIDEO
		L-1 OUTPUT						S-VIDEO
		L-1 INPUT				SCART VIDEO
		L-2 SELECT				VIDEO

	SET UP		ENTER SELECT WITH @ THEN PRESS [ENTER]
	EXIT			PRESS [SET UP] TO EXIT
	EXIT		SELECT

Rear of unit

Note for connection:

Remove the protection cap from the optical cable.

1	Connect the unit and a digital audio device using either an
2	optional optical cable or an optional coaxial cable.
2	Place a disc on the unit and load an MD on the connected

* The boldface settings below indicate the settings at your purchase.

8F-1 INPUT ^ VIDEO / S-VIDEO VIDEO:

digital audio device.

3 Select the audio to be dubbed.

When connecting an appliance to the [VIDEO] input connector, set to A VIDEO B.

S-VIDEO:

When connecting an appliance to the [S-VIDEO]input connector, set to A S-VIDEO B.

5Press W to pause playback.

6Select the input mode on the connected digital audio device.7Press I to start playback on the unit.8Start recording on the digital audio device.

9Stop recording on the digital audio device. Then press oto stop playback on the unit.

NOTE:

There may be a discrepancy of several seconds between where you intend editing to start, and where it actually starts.